How To Remove Paint From Interior Brick

How to Remove Paint to Expose an Interior Brick Wall

Removing paint off brick can bring back the original appearance, but it is not a simple operation. Because brick is porous, paint seeps into all of the cracks and crevices in the surface. In addition, interior walls cannot be simply water- or sand-blasted, since they cannot be done with wood scrapings. The option for interior walls is to use chemical or gel masonry strippers; however, while the process of stripping the brick is not hard, it does require numerous applications of stripper and a great deal of scrubbing, which makes it a time-consuming operation to complete.

  1. Floor protection should be provided by thick dropcloths or plastic sheeting, which should be secured to the wall using duct or painter’s tape. By painting with a tiny section of the bottom of the wall, you may evaluate how well the masonry paint remover adheres to brick and how well it removes paint. Instead of concrete, the stripper should be designed specifically for brick. It will be necessary to apply a second compound to safeguard the brick wall if there is a negative response, such as the brick or mortar collapsing. Protect your eyes and hands with safety goggles, a face mask, and work gloves to prevent accidental contact with the stripper chemicals or fumes. Pour a little amount of the masonry paint remover into a small bucket or container and shut the container back up. Carefully position the ladder at one corner of the wall before climbing up
  2. Starting with one corner of the brick wall and moving outward and downward, generously brush the masonry paint remover over it with the brush. As you work your way around the top of the wall, reposition your ladder so that you may work on each part until all of the brick has been covered with stripper. The manufacturer has provided a period of time during which you must wait Then, starting at the top of the wall, scrape the masonry paint remover off with a stiff-bristled brush to remove any remaining paint. It is necessary to continue to wear protective clothing even though the paint will come off in chunks and flakes. Remove as much of the paint as possible off the wall by scrubbing it with the brush. Wash the brick wall with cloths and warm water to remove any adhering paint or stripping compound that has formed on the surface. Allow it to dry naturally
  3. Reapply another layer of masonry paint remover to remove any remaining paint that has become tenacious. Allow it to rest on the block for a while before scrubbing it again. This process may need to be repeated numerous times in order to remove the majority of the paint from the brick wall. To completely remove the stripper, repeat the rinse procedure. To remove any residual paint residue from the brick wall that has been scraped, spray it with white vinegar and scrub it with a clean brush. Using water, rinse the area.

Things You Will Need

  • Ladder
  • Dropcloths or plastic sheets
  • Duct tape or painter’s tape
  • Masonry paint remover
  • Paintbrush
  • Safety goggles, face mask, work gloves


Exhaust fumes through open windows and doors; if feasible, use a fan to bring fresh air into the room as well as fresh air from outside.


  1. It’s possible that lead-based paint was used on the brick, depending on how old the paint job was at the time. Before you begin, get the paint tested
  2. If lead paint has been used, call a professional who is qualified in lead paint removal to do the process.

How To: Remove Paint from Brick

  • Stripper
  • Paint remover strips
  • Work gloves
  • Protective glasses
  • Respirator mask
  • Drop cloths
  • See complete list » Tape for painting
  • A trowel and a stiff-bristled brush are required.

Image courtesy of

How to Remove Paint from Brick

  1. Test the stripping agent on an inconspicuous portion of the installation before applying it to the entire installation to remove paint from the brick. It’s possible that the stripper you’ve chosen does not perform as well as you had hoped, or that the brick was painted to mask its bad state to conceal its poor condition. Another compelling reason to begin with a test is as follows: This will give you an idea of how much work will be required to complete the task. You may still decide to hire a professional, or you may decide that you can put up with the paint after all
  2. There is no doubt that this will be a dirty endeavor. Preparing your work environment in a methodical manner will help you to save clean up time. Put down a series of drop cloths or a thick plastic sheeting to capture the peeling and flaking paint that will fall away from the brick. Next, start painting. Keep in mind to secure the drop cloth or plastic to the bottom edge of the brick using masking tape. Invest the time to properly cover any surrounding painted surfaces—such as the adjacent wood trim—with painter’s tape. Also, make sure you’re wearing the safety gear advised by the maker of your selected paint remover to avoid damaging the finish of those surfaces. Preparation for applying the gel or paste begins with scraping away any loose paint that has already come free. After that, apply the compound to the brick using a trowel or a specific instrument given by the paint remover maker. Make careful to push the gel or paste into all of the cracks and crevices in the brick and mortar, and to do so thoroughly. Build up the stripper layer by layer until it reaches the thickness required by the manufacturer
  3. After the stripper is in place, begin arranging the peeling strips as instructed. These strips, which are often composed of cloth, should be pushed and held against the stripper until they are securely bonded. Overlap the strips such that no brick can be seen between them. Following application of the strips, allow them to cure for the amount of time specified by the manufacturer. Most of the time, especially when there are numerous paint layers to consider, it takes a full 24 hours for the compound to dry and begin to work its magic. Return to the work area once a suitable amount of time has elapsed and begin raising the strips off the ground. In order to acquire purchase behind any slow strips, you may need to use the trowel. Continue to peel the pieces in a steady and careful manner
  4. Avoid ripping them. As you peel away the paint, the paint beneath it should come off with it. Use the trowel to flake away as much of the compound or paint residue as possible where the strips have left behind. If the trowel isn’t cutting it, clean the area with a stiff-bristled brush before rinsing well with water. If it wasn’t previously obvious, the following is now: Removing paint off masonry is a time-consuming, if not downright exhausting process.

Follow the manufacturer’s directions for removing and disposing of the spent strips. Some items’ chemical reactions come to a halt on their own, while others require the addition of a neutralizing agent to bring them to a complete halt. It’s also vital to note: If there is any danger that the temperature may dip below freezing within a month or so after attempting to remove paint from brick, do not proceed. In particular, if the brick does not have a chance to cure entirely before the frost, it will be more susceptible to damage.

Receive free, no-obligation quotes from professional painters in your area.

How to Remove Paint From Brick

It’s possible that a lovely brick fireplace or wall is hiding below that layer of paint. It is your goal to remove the paint off the brick, despite the fact that the paint was someone else’s vision (or your own past project). It is feasible to remove paint off brick in small areas, such as interior walls or fireplaces, with the correct materials and a little concentrated work, so returning them to their former condition.

Before You Begin

When removing paint off inside brick, the best procedure is to apply a non-caustic paint remover, scrape, and then brush the paint away. A good paint stripper can make the work a little simpler, but it’s still a manual process that takes time—which is why removing brick off the outside of an entire home or structure is a lot easier said than done—but it’s made a little easier with an efficient paint stripper. The interior of your home might be damaged by high-pressure washing and sandblasting.

Paint strippers will not remove all of the paint off your walls, but some will do it more effectively (and safely) than others.

Purchase a gel-based paint remover to remove paint off vertical surfaces such as walls and fireplaces.


Purchase about one gallon of gel-based paint remover for every 75 square feet of vertical surface area if you are painting vertically.

Paint remover will be used in two, three, or even four coats, depending on the situation. A typical-sized fireplace is around 25 square feet in size. Six linear feet of inner brick wall equates to approximately 48 square feet of space.

Codes and Permits

If you want to strip paint with a paint remover that contains methylene chloride, you may be required to get a permission to do so or to adhere to particular emissions control measures in order to use the product. Environmental protection agency (EPA) regulations govern the use of such items to minimize emissions, and the standards vary depending on when, how, and to what extent the stripper is employed in a given situation.

Safety Considerations

Despite the fact that there are paint strippers available that do not include methylene chloride, the majority of these products are still potentially harmful. Maintain strict adherence to manufacturer’s recommendations, and operate in a well-ventilated location while wearing chemical-resistant gloves, glasses, and protective clothes.


  • Paint stripper, plastic sheeting, painter’s tape, lead paint test kit, and TSP are all items you’ll need.

Test Paint

  • To test for lead paint, use the lead paint test kit to slice off a little bit of paint and submit it to the laboratory. After confirming that the sample does not contain any lead, proceed with removing the paint off the brick. As soon as lead is discovered in the paint, a lead abatement contractor will be called in to complete the task.

Add Plastic Sheeting

  • Securely tape down plastic sheeting on the floor in front of each brick and around each brick on each wall, using a strong adhesive. Increase the length of the sheeting on the ground by at least 6 feet, and the length of the sheeting on the walls by 3 feet. Wrap up any surrounding furniture or other things that cannot be transported
  • And

Clean Brick

To the clean bucket, add the TSP and warm water and stir well. Heavy deposits of soot on fireplaces should be cleaned up with cooking gloves on. In order to successfully peel the paint, it is necessary to remove any debris or soot that may have accumulated throughout the painting process.


  • Only clean the brick if it has become excessively unclean or discolored. If there is only a little amount of debris and dust, skip the cleaning stage and proceed with the paint peeling.

Apply Paint Stripper

  • Paint remover should be applied to the brick while wearing safety gear. Apply the stripper in thick layers, rather than thin ones, since thin layers dry too rapidly.

Scrape Paint

  • To determine the degree of firmness of the paint, use the putty knife to test it. The paint should be applied in a thick, goopy coating that is soft all the way down to the surface and easily removed with a putty knife after curing for many hours. Remove the paint with a scraper and place the remaining paint in a garbage bag

Apply Second Coat of Stripper

  • After the first coat of paint has been removed, some paint will remain on the surface. Second, apply a second coat of stripper and allow it to set for about 4 hours, or for the length of time recommended on the product label

Remove Remaining Paint

  1. Remove the second layer of paint with a putty knife and let it dry. Remove the remaining paint from the brick as soon as possible by rubbing it with steel wool or a steel-bristle brush.

Tips for Removing Paint From Brick

  • To slow down the drying process if the paint stripper is drying too quickly, put a piece of plastic over the area to be painted. Don’t scrimp on the paint remover when it comes to application: Greater strength is achieved through thicker layering than with thin layering. It takes a lot of effort to strip paint, so plan your time carefully and avoid working for too long during each session. Keep an eye on the specified timings for the paint stripper. Leaving the paint to dry for too short a period of time does not give the stripper enough time to work, while leaving it for too long causes the paint to harden anew. Work in little parts at a time. Continue with the following part when you have done with the previous one.

When to Call a Professional

When it comes to large-scale painted brick removal, it’s usually preferable to hire a professional. If the lead paint on the brick is found to contain lead, contact a competent lead abatement firm.

How to Remove Paint From Brick in 8 Steps

The comfort element of a property may be quickly increased by using brick. A home’s beauty and appeal are instantly boosted by exposed brick walls, brick fireplaces, and brick exteriors. When done well, painted brick can easily make a property appear like it’s out of a storybook. However, if painted brick is done incorrectly, it might scare away potential purchasers. In case you’re looking at a property or feature that falls into the second group and would like to discover the quickest and most effective approach to remove paint off brick, continue reading.

How to get paint off brick, step by step

Prior to 1920, brick was mostly composed of lime and sand, a combination that causes the material to disintegrate over the course of a century. Nowadays, the majority of bricks are constructed of Portland cement, which is a more robust and long-lasting substance than clay bricks. Have a masonry business analyze the condition and make repairs before proceeding with the next measures if you know for certain that your home is constructed of lime and sand brick or if you see an excessive amount of crumbling and cracking.

See also:  How To Build Interior Stairs

Step 1: Organize your workspace

There will be a mess, just as there will be with any other outside and home repair project. Cover the ground beneath the brick with drop cloths or plastic to prevent it from becoming contaminated. It takes time and effort to remove paint flakes off plants and to sweep them up from the floor. It may take you hours to complete the task. Place all of the required tools in one convenient spot that is easy to access.

Step 2: Test a small area first

Test the stripping compound on a tiny, out-of-sight area first to ensure that it performs as intended before applying it more widely.

This test is also important in determining whether or not the paint was applied with the intent of concealing any maintenance concerns.

Step 3: Remove loose paint

Scrape away as much paint as you can from the surface before applying the paint stripping compound in a frantic effort to remove it all.

Step 4: Apply the paint stripper

It’s time to start removing the paint off the walls. Begin by using the tool that was given by the manufacturer. If a tool isn’t present, atrowel will suffice in its place. Cover every single brick with the stripper, then drive it into every crack and crevice you can find. Apply as much paint remover as the manufacturer’s instructions specify. It is possible that you may need to apply several applications of paint stripper to complete the task.

Step 5: Apply the peeling strips

Following the application of the stripper, apply peeling strips across the whole surface area. These strips, which are often made of cloth, should be positioned such that they overlap each other and cover every single brick. Each strip should be pressed firmly against the stripper chemicals.

Step 6: Wait for the magic

Wait until the stripping compound has completely dried after applying all of the strips. This varies depending on the manufacturer, but in many circumstances, you will be required to wait for a full 24 hours before using the product.

Step 7: Remove the strips

After the proper length of time has elapsed, you will be able to take the strips from the jar. Make sure to move gently and methodically to prevent damaging your clothes. Remove any remaining paint stripping chemical or residue from the surface using a trowel. If it doesn’t work, warm water and a stiff-bristled brush should do the job.

Step 8: Dispose of the strips

Dispose of the strips in accordance with the manufacturer’s instructions to ensure proper disposal. Remember that you may have to soak them in a neutralizing chemical before you can dispose of them properly.

Products and tools you’ll need to get paint off brick

  • Dropcloth: Using this will assist you in keeping your work space clean. In certain cases, purchasing many packs and laying them down all at the same time may be more effective depending on the size of your property. Paint stripper: Look for a brand that is safe to use on brick, or one that has been particularly developed for this purpose. Keep in mind that most brick stripping compounds are effective on 45–50 square feet of brick
  • Thus, plan accordingly. Despite the fact that many paint stripping companies include paint removing equipment, it’s best to be on the safe side and acquire your own trowel. The fact that they are reasonably affordable also means that they may be utilized for other home renovation tasks. The moment has come to acquire a ladder if you don’t already have one. The ideal option is an aladder that extends up to 10 feet, which is very useful if you have a two-story home. Disposable gloves: When dealing with paint stripping chemicals, disposable gloves should always be worn. Given that most chemicals contain eye irritants, keeping your hands clean is critical to your safety
  • Nonetheless,

Don’t want to use harsh chemicals? Here’s how to remove paint from brick naturally

Chemicals used in paint stripping compounds may be dangerous to your health and should not be used in your house. Fortunately, when it comes to removing paint from brick, you have a number of options to choose from. Power washing and sandblasting are two more typical ways of cleaning. These may be the most straightforward solutions for you, depending on the state and material composition of your bricks. If you pick either approach, make sure to always wear safety glasses while performing the tasks.

The bottom line

The procedure of removing paint from masonry is time-consuming and difficult. Getting through it will take you more than a day because it is highly physically demanding and stressful. Before deciding whether to use a paint remover compound, a power washer, or a sandblaster to remove paint off brick, carefully check the bricks to ensure that they are not in bad shape. The use of a paint remover is the safest method since it maintains the structural integrity of your brickwork, even though power washing will take the shortest period of time.

Frequently asked questions

Is it possible to repair painted brick? It all depends on how well the brick is preserved. Using a couple of coatings of liquid cement hardener to remedy the problem and then removing the paint with a stripping compound might be a good solution if you see any brick degradation in a few locations. Is it possible to pressure wash the paint off the brick? When it comes to removing paint off brick, pressure washing is one of the most preferred methods. Prior to proceeding, you must check the brick to identify whether or not any erosion has happened, in order to prevent more harm from occurring.

The services of an expert might be beneficial if you are unclear about the procedure to employ for this project or if the quantity of brick deterioration you notice makes you feel uncomfortable.

What kind of weather conditions are required to remove paint from brick?

If your bricks do not dry completely before a frost hits, you might be in for some serious brick degradation problems.

What is the maximum number of layers of paint that a paint stripping compound can remove? This is highly dependent on the particular brand you’re utilizing. The majority of paint stripping chemicals are capable of removing three coats of paint.

How To Easily Remove Paint From Brick [2021 UPDATED] – ThatPainter

When it comes to brick walls, removing paint is not a simple task, especially if you want to preserve the brick wall underlying the paint intact and in excellent shape. Furthermore, employing the incorrect procedure to remove paint off brick will make it more difficult to remove and may cause damage to the wall itself, further aggravating the situation. For your convenience, we’ve put up a tutorial that will show you precisely how to remove paint from brick in no time. It may need a small investment of your time, but the results will be well worth it!

The basics

First and foremost, before we get into a full explanation on how to remove all of that paint, there are a few crucial items to keep in mind. Before you begin attempting to remove the paint, it is critical that you determine what sort of paint you have on your hands. Latex-based paints and oil-based paints are the two most prevalent forms of paint that are used on brick walls. As a result, this instruction will cover the removal of both of those types of paint.

External factors

There are various external elements that must be taken into consideration while removing paint off bricks, in addition to the type of paint being removed. These considerations include the materials required to peel away the paint, the compatibility of any goods you may like to employ, the environment and temperature in which you will be working, and the clean-up that will be required following the removal of paint. Let’s take a closer look at each of them.

Materials and products

While metal wool and forceful scrapers may appear to be a failsafe method of removing paint off brick, they might really cause more harm than good in the process. It is doubtful that it will completely remove all of the paint, and it may even cause harm to the wall itself in some situations. When it comes to solving problems, sometimes the most obvious options turn out to be the worst course of action. The best substance for removing paint off brick isn’t actually a material in the traditional sense.

Most of the time, this solution comes in the form of a liquid or paste paint remover that is specially intended to penetrate deep into the brick and any gaps into which paint may have leaked over time.

Paste strippers are our preferred method since they are less difficult to work into the wall.


Now that you are aware that a paint stripper is required, we wanted to take this opportunity to remind you that you cannot use any paint remover at your discretion. If your brickwork has been painted with masonry paint, it is probable that you will have some difficulty removing it unless you use a paint remover that has been specifically formulated for the removal of masonry paint.

In addition to requiring a masonry paint stripper, you need make certain that it is a drip-free liquid that does not include methylene chloride and that it is not a spray remover. The result will be that you will be able to operate the stripper safely and much more readily as a result of this.


Provided that you follow our recommendations in the preceding section and choose a non-drip stripper, ideally one that does not spray, the amount of clean-up should be limited to a bare minimum. It is critical to implement the proper cleaning procedures, such as placing a towel or sheet on the floor to catch any drips. For example, if you are renovating a brick wall in your house or a brick fireplace and want to maintain it looking clean and attractive, this is very important to remember.


Of course, we understand that you have no control over the climate, but it is important to remember that exposed brick is subject to breaking in extremely cold or hot temperatures. If you intend to remove the paint during a period when temperatures are below freezing, keep in mind that the longer the brick is exposed to the elements without the paint, the more damage it may experience from the elements. In order to ensure that you have enough time between stripping the brick wall and restoring it, we recommend waiting until the weather is warmer before beginning the restoration process.

How to remove paint from brick: a guide

  • Masonry paint stripper of choice
  • Wire brush
  • Drywall knife
  • Protective clothing (goggles, painting overalls, long sleeves, and a facial covering if necessary)
  • A masonry paint stripper of choice Sheets of plastic
  • Clothes that have seen better days

Easy guide to removing paint from brickwork and brick walls

It is vitally critical that you examine a potential problem location before proceeding. Test at least two or three bricks in a place that is largely out of sight, and do it in a confined space. Follow the directions on the label of the masonry paint remover you’re using. Remove a little quantity of stripper from the container and apply it to the test area. Following the application of the glue (as thick as the quantity of jelly or peanut butter you would spread on a sandwich), you may cover it with a plastic sheet to keep it from drying out.

If the paint is starting to break away from the brickwork, you’ll want to take note of it as well.


Hopefully, you have selected a stripper that meets your requirements and are ready to go with the rest of the process. To begin, you must carefully clean the space in which you will be working. For exterior walls or on a fireplace, this is very important to keep in mind. Make use of your yard hose to accomplish this if at all feasible! If this is the case, physically clean it down using a big bowl, bucket, or pail of water and a rag if necessary. While this step makes the paint removal approach much simpler, it is not required, and if your brickwork is in clean, good condition, you may skip this step if you so like.

Allow for complete drying of the wall before using any paint stripping products.

As soon as you are certain that the wall has been thoroughly cleaned and dried, you may prepare the space around it by laying down old clothing and sheets to catch flaked-off paint, any drips of the paste or liquid, and any other debris.

If you’re outside and it’s windy, it could be a good idea to tape the sheets down or put big garden pebbles in a corner to keep them from blowing away.

Protect yourself

Now that you have arranged your workstation, you must ensure that you are secure in your surroundings. This implies that you must take all required precautions to protect yourself from caustic paint strippers, dust, dirt, and flaking paint that may have accumulated over time. All of these substances have the potential to be irritating to the skin, lungs, and eyes. As a result, we strongly advise you to put on eye goggles, protective clothes such as painter’s overalls and long sleeves, and maybe even a pair of work gloves when painting.

Apply the stripper

You are fully prepared, your wall has been prepared, and the area has been safeguarded – now comes the exciting part! Grab your masonry paint remover and turn it on to the highest setting. Regardless of whether you have selected a paste or a liquid recipe, you should take your drywall knife (or a putty knife if you want) and apply the product to the wall or brickwork. Apply the stripper thickly (this is one of the reasons why we believe paste is the ideal formula), preferably using a wire brush (with firm, stiff bristles) if you want to make it easy on yourself or if you have a larger area to cover.

Work fast to complete this task because you will want to guarantee that the plastic sheet is applied before any of the strippers have had a chance to dry.

The plastic sheeting should be applied in a clean manner, with any air bubbles being smoothed down so that it is perfectly flat.

See also:  How Wide Is A Standard Interior Door

When you have finished applying all of the stripper and plastic sheets to the brickwork, you should leave them on the brickwork for the appropriate amount of time.

Remove the paint

After the stripper and sheets have been left on the brickwork for the prescribed period of time, you can proceed to remove them off the brickwork without further delay. To achieve this, you should grasp a corner of the plastic sheet and forcefully pull it off, making sure to remove all of the sheets as quickly as possible so that it does not break. Under the sheet, you should be able to see that the paint has also peeled away, either peeling away with the sheet or clinging loosely to the wall beneath the bed sheet.

  • Fortunately, this paint is going to be loose and flaky, and it will be easy to scrape away with a razor blade.
  • Be cautious not to harm the exposed brick by using the paint scraper carelessly.
  • You might go through the process again to deal with this (we recommend doing this if there is a large area that is being stubborn).
  • Remove all of the paint and debris from the brickwork before washing it off with a hose or a bucket of water to complete your brickwork restoration project.

If you wanted to, you could also use a power washer at this stage if necessary. After that, you may go ahead and repair it in any way you see fit.

Frequently Asked Questions

The answer is no, it is unlikely that vinegar will alone be sufficient to remove masonry paint off brick. While it is useful for removing difficult spots of paint after a paint remover has been used, it will not be sufficiently abrasive to remove touch masonry paint from broad expanses of brickwork.

What is the best masonry paint stripper?

Masonry paint remover is most effective when applied in paste form since it may be applied in thick layers with ease. Sunshine’s Multi-Strip Advanced Paint and Varnish Remover, which is methylene chloride free and masonry paint confirmed, is the product we propose for you.

Final verdict

Finally, a comprehensive tutorial on how to remove paint off brick has been provided for you. We are certain that you will agree that it is less difficult than you may have anticipated. Remember, if you use the wrong approach, you might end up doing more harm than good, so follow our tried and true procedure, get some of our favorite masonry paint strippers, and begin scraping!

How to Remove Paint From Brick (5 Easy Steps)

Removing paint off brick isn’t as difficult as it appears. In fact, regardless of the sort of paint you use, this quick and simple five-step approach will assist you in getting the job done correctly, quickly, and efficiently. Expect this to take a significant amount of time. Set aside at least three hours every session, with the understanding that two to three sessions may be required. Fortunately for you, we’ve put up a comprehensive list of everything you’ll need to complete this very simple DIY project.

What You Need to Know About Removing Paint from Brick.

Like everything else, it just takes a few tries to build a method and a familiarity with the material that will help you in the future. Here are some of the fundamentals you’ll want to be aware of before getting started. Latex paint is the most commonly seen form of paint that individuals seek to remove off brick. This guidance may be used for each of these purposes, as well as for oil painted walls. See this in-depth ProPaintCorner tutorial for more information on removing spray paint off brick and other hard surfaces.


After you’ve finished restoring the brick, make sure it won’t be exposed to freezing conditions for at least three days after you’ve completed the restoration. Extreme cold may readily harm masonry that has been exposed.


It’s unlikely that aggressive scrubbing with a scraper or steel wool will completely remove the paint. Because brick is porous, a caustic paint remover is necessary to loosen the deeply imbedded paint particles from the brick cracks. For more information, please see the following YouTube video on how to choose the best methylene-free paint stripper for the job at hand:


Strippers are different from one another. For the greatest results, seek for a brand that is specifically promoted as being developed for masonry applications. Spray strippers should be avoided since they are less effective.

Those containing methylene chloride as an ingredient should be avoided. Formulas that do not include methylene drip significantly less than those that do. Methylene chloride, despite its simplicity of use, is exceedingly hazardous, as evidenced by the following.

Clean Up

When working indoors, especially on works like brick fireplace restoration, put in extra care in your preparation so that when it comes time to clean up, it is simple. That entails placing fresh drop cloths with care, taping them down wherever feasible. When the repair work is finished, carefully detach the tape that was used to secure your drop cloths. The cloths should be folded in from each corner to ensure that no debris spills onto the floor. More information can be found at What is the best way to remove spray paint from bricks?

Supplies You’ll Need When Removing Paint From Brick

The majority of this task will consist of scrubbing the brick surface with a caustic paint remover for the majority of the time. Most paint strippers are available in the form of a thick paste, which may be applied with a brush or a putty knife to remove old paint.

  • Drop cloth, plastic sheeting, painter’s tape, safety glasses, long-sleeved shirt, drywall knife, protective painting equipment, peeling strips (maybe), and a stiff-bristled wire brush are all items you will need.

Read moreWhat Are the Most Effective Techniques for Removing Spray Paint Anywhere?

How to Remove Paint From Brick (5 Easy Steps)

  1. Protective Gear
  2. Apply
  3. Clean Up
  4. Test
  5. Clean and Prepare
  6. Protective Gear

Step 1: Test

The first step in removing paint off brick is to test the brick with the paint stripper before proceeding with the process. Setting aside a small section of around 2-3 bricks that is low, in a corner, or otherwise non-focal is recommended. Take your putty knife and work a little quantity of material into your test area before applying it to your final area. Cover the area with stripper material, followed by a covering of plastic to protect it. After 30 minutes, make an attempt to remove the sheeting from the window.

Anything else, and you’ll want to try a different stripper brand on your next outing.

Step 2: Clean and Prepare

Completely clean the area before using your stripper to prevent contamination. Using the wet rag, apply lukewarm water to the block, rubbing the water in with your hands as you go. If the situation calls for it to be done outside, a garden hose should be used if one is readily available. Consider carefully scraping your brick with a metal putty knife or a wire brush to remove any peeling paint that has accumulated over time. Although it is not absolutely required to wash your brick prior to using a stripper, doing so helps to make the process run more smoothly and efficiently.

A drop cloth should be placed beneath the work area as the final step in preparation for application.

If there is a possibility that your fabric will blow around, tape it down.

Step 3: Protective Gear

The bare minimum list of protective equipment that you’ll want to wear while working on this project includes the following items:

  • Long-sleeved shirt, goggles, facemask or respirator, and work gloves are all recommended.

See this CSPC guidance for information on how to properly use a respirator when using paint strippers.

Step 4: Apply

Make sure you have enough of plastic sheeting and paint remover on hand, as well as your putty knife. Using your putty knife, scoop up the stripper and begin to spread it onto the painted brick surface. Spread it on approximately as thickly as you would peanut butter on a sandwich, if that makes sense. This should be done over the whole area, making sure that the stripper does not have a chance to dry before you cover it with sheeting or plastic. For the sake of simplicity, you can consider cutting your sheets into 3ft square portions.

Step 5: Remove

30 minutes after laying the plastic sheeting on the brick surface, you will begin to remove it using a plastic scraper. Once that time has expired, proceed to carefully peel aside the plastic sheets to reveal the underlying structure. You should be able to see the paint remover and paint peeling away from the walls, with exposed brick left in its place. When you peel back the plastic sheets, you should notice that much of the paint has come off with it. Using your putty knife, try to scrape away any residual paint or stripper from any remaining places.

More information can be found at What Is the Best Way to Remove Spray Paint From Walls?

Other Valuable Resources For Removing Paint From Brick

This guide has been created with best practices in mind at every step of the way. However, always read the whole manufacturer’s instructions for any paint thinner or other chemical solutions you intend to use before beginning any project. Any instructions or safety precautions provided here should be revised to reflect those provided by the manufacturer. Keep in mind that many applications may be required to completely remove all traces of paint from the surface. Another option is to finish your stripped brick wall with white vinegar, which may be applied as a finisher.

Taking paint off a brick fireplace, pt. 1 — Salt & Rook

The following is an update to one of our most popular pieces, since there have been some changes to the project after the original publication of this post. Thank you for taking the time to read this!

  • The following articles were published in February 2017: Taking Paint Off A Brick Fireplace, Part 2
  • March 2017: Taking Paint Off A Brick Fireplace, Part 3
  • August 2018: Why We’re Painting Our Brick Fireplace
  • And September 2018: Why We’re Painting Our Brick Fireplace.

Our initial impression of this property was the painted brick fireplace, which was one of our first observations when we first walked through the door. We adored the fireplace, but we were well aware that the paint would be one of the first things to be stripped away. Homes and interiors designed in the arts and crafts style are common in the Syracuse University district. However, painting over the brick and stained wood walls, trim, and doors that give arts and crafts style homes their charm is becoming increasingly trendy.

  • I mean, this appears to be rather appealing.
  • After some research, it was discovered that there are several tutorials for painting a brick fireplace.
  • Although there were no manuals available to assist us through our first job, we discovered some inspiration on the site 1914 Foursquare and their fireplace repair project, which we followed to completion.
  • At the very least, we were aware that we would need to use a chemical paint remover first.

Side note: Because the blog was only a concept when we first started working on this project, all of the photos were shot using a phone and were taken at night in poor lighting. Better-quality images are on their way to you.

Step 1: Gather supplies

We went a little crazy at Home Depot and bought everything we thought we would need, including the following products:

  • Putty knife
  • A multi-strip paint and varnish remover
  • A cheap paintbrush (such as this—something you don’t mind throwing away)
  • And a paint scraper. Brushes made of wire (such as these)
  • Sponges, paint buckets, plastic sheeting, duct tape, and painter’s tape are all useful tools.

Step 2: Prep and applying multi-strip

Preparing the room included removing all furniture and mantle, as well as placing and taping a plastic sheet to the floor and walls. After that, we began work. It was important for us to build airtight seals around the areas where the tarp would preserve the hardwoods. Around the mantle, the wall was painted in a contrasting color. Despite the fact that the mantle may be removed, you can see where a former owner painted the walls surrounding the mantel without first removing the mantle itself.

Actually, Pat finished the first layer of multi-strip while I went out to supper with a buddy.

However, he just “painted” it all over the fireplace using a cheap paintbrush to save money.

The texture surprised me because I was expecting something more like a paste.

Step 3: Wait

This may have been the most difficult aspect of the process. Seriously. When the paint is nearly bubbling off the walls, it’s difficult to refrain from scraping it off. Is it possible that we’re weird? Yes, without a doubt. A close-up of the multi-strip remover in action, melting paint off of a brick surface.

Step 4: Scrape the crap out of your fireplace

The multi-strip had been working its magic for almost 2 days when we put on our worst clothing and started scraping. I’m not going to lie: it took several hours to complete this process. Scraping was a systematic process as we attempted to remove as much paint from the brick and mortar as humanly feasible. We threw the paint scraps into a rubbish bag, but as the day wore on, we kept forgetting to put the garbage bag back where it belonged and walking into jelly-like paint blobs. As a side note, we purchased nitrile gloves to protect our skin, however the multi-strip almost completely disintegrated them right off our hands.

We were, however, still a little embarrassed.

After we completed scraping, we cleaned the brick with metal brushes and warm water to remove any remaining debris.


Step 5: Repeat

Yes, you are correct. We went through the full procedure twice. After cleaning the brick, we immediately went back in with the multi-strip to finish the job off. Just before scraping off the second layer of multi-strip, take a deep breath. We glopped on the second coat superthick and let it dry overnight. When applying the multi-strip, we discovered that the thicker it was put, the simpler it was to scrape off. We let it to sit for about 2 days before doing the same scraping and scouring procedure once again.

  1. The finished product: This is what the brick looked like after two applications of multi-strip paint remover.
  2. We scraped off at least three coats of paint, including a layer of pink paint, and I’m not kidding when I say it was a lot of work.
  3. Pat returned later and scraped paint off the bricks at the bottom of the foundation.
  4. At the end of the day, it was virtually identical to the others.

We believe it is an oil-based paint, maybe even a paint intended for use on the exterior of a building. How did we come to the decision to delete it? We’ll go into more depth about this in Part 2. We discovered a few of things as a result of this project:

  • Duct tape should not be used on your walls. It’ll tear the paint and sections of your wall right off the wall. Make a better decision than we did and utilize the blue painter’s tape. Even though we’re intending to repaint our walls later, the wall surrounding the fireplace looks quite shabby right now
  • Despite how difficult this process was, we enjoyed using the multi-strip remover to get the job done. When used on latex paints, it works quite well, and scraping it off felt strangely pleasant. Rather than painting or whitewashing a brick fireplace to “brighten” your area, you might want to think about other alternatives. This is especially true if your home is older or has any historical design elements. As we’re discovering, this alteration is essentially irreversible unless someone is prepared to put in a significant amount of time and effort into undoing it (which is exactly what we’re doing right now!) or a significant amount of money into replacing it. We’re not saying don’t go ahead and do it. We’re only cautioning you against painting a porous surface such as brick or stone as a “quick fix” for your area just to save time. It’s because if you don’t like it, you’ll be stuck with it.
See also:  How Many Years For Interior Design

How to Remove Paint from Brick

“I have a brick entryway on the inside,” Laurie explained. It appears like paint got on a fifth of the bricks during the priming process for the walls and ceiling. Do you have any suggestions for how to clean and perhaps polish them? A pressure washer cannot be used indoors due to the danger it poses.” Some individuals love the painted look of brick, while others prefer the more natural appearance. Fortunately, brick is a durable surface that can be easily transitioned from one color to another and back again if desired, but it would be simpler to simply put a fresh coat of paint over the first if all you want to do is change the color of the paint.

These procedures can be applied to a brick wall on either the inside or outside of a building.

Removing the Paint

  • The following items: commercial paint remover, a wooden scraper, a wire brush, steel wool, water (a sponge), a bucket, and a towel

Steps to Remove the Paint:

  1. Make sure the place is adequately ventilated. Make use of a paint remover, such as Peel Away 7, on the painted portion of the brick
  2. Allow the paint remover to dry completely. Scrape off the paint with a wooden scraper, a wire brush, or steel wool to remove the excess. After the paint has been removed, the bricks should be rinsed with water. Using a pail of water, sponging it onto the brick is an easy way to accomplish this. To dry the brick, use a cloth to pat it down.

Additional Tips and Advice

  • When working with a paint-remover, always wear gloves to keep your hands protected. 1
  • Sandblasting the paint off is an option to scraping it off by hand, albeit it is better left to a professional to do so safely and effectively. 1
  • There are certain varieties of ancient brickwork that are softer than others and might be harmed by a cleaning that is overly aggressive. When washing your bricks, proceed with caution until you are confident that they will bear the strain. 2
  • Interior brick is more prone to grime and stains than outside brick due to its location. Once the paint has been removed, your brick will be exposed to the dangers of the environment. You might consider sealing the wood and also applying a coat of paste wax to keep it protected and polished. The Paint Removal part of the articleHow to Clean Exterior Brick contains information on how to remove paint off exterior brick.


  1. Jeff Bredenberg’s Clean It Fast, Clean It Right is a guide on cleaning quickly and correctly. Making It Clean by Jeff Campbell and The Clean Team
  2. Martha Stewart’s Homekeeping Handbook
  3. And more.

Reader Interactions

That brick wall was certainly attractive at one point, but it was later painted over by someone who didn’t like for it. Why? Who knows what will happen. We could spend the rest of our lives debating the aesthetic preferences of others until we’re blue in the face, but why would we? We still want to repair that traditional brick surface, which has a coating of old, rubbery rubbish smeared across it. Given the difficulty of the task, we created this essay on how to remove paint from brick without damaging it.

Inspect Before You Quote

Unfortunately, paint removal from brick is certainly among the top ten “stubborn occupations” on the list of the most difficult tasks. Many do-it-yourselfers have started the project just to be unhappy with the outcome. Alternatively, they may have been satisfied with the results but had unknowingly weakened the brick as a result of their efforts. Considering these facts, it is recommended that you evaluate the task properly before providing an estimate to any prospective clients you may have.

For this frequently time-consuming job, it is more probable that you will find yourself having to revise your original quote.

Assessing the Integrity of the Wall

First and foremost, you must assess whether the brick will be attractive enough to be left unpainted. Inquire with your customer about the possibility of inspecting and perhaps testing a removal technique in an inconspicuous location. How many coats of paint are there in total? What is the condition of the brick? Using a test area, it will be much easy to offer (or not quote) a price. Following your testing, you and your customer may decide that the expense of paint removal outweighs the advantages, and they will just learn to live with the painted brick in their home or business.

Avoid Pressure Washing or Sandblasting

The following are some things you should avoid doing if your project receives approval: First and foremost, while it may appear that sandblasting or pressure washing the painted brick would be beneficial, it is not. Older, fragile brick might be weakened or damaged by this treatment. It’s possible that this was the motivation behind the painting in the first place. When working with old brick, utilizing a high-pressure washer that is too powerful can have disastrous consequences for you. Additionally, if the paint is old, it is likely that it contains lead, which is released into the air during sandblasting.

Porous brick can be cleaned by sandblasting or pressure washing, but these methods are frequently too dangerous to use on a large surface area. Although it is not possible to establish the presence of lead paint just by looking at it, test kits are readily available online.

Avoid Using Caustic Chemicals

When removing paint from brick, you’ll want to stay away from caustic chemicals as much as possible. These methods have the same negative impact on older brick surfaces as sandblasting, which is why they are not recommended. It can also make ancient brick more fragile if it is exposed to moisture. The ultimate goal is to find a remedy that does the least amount of harm to the underlying brick, and employing these methods may leave you with a greater problem than just a resistant coat of paint to contend with.

Please continue reading.

How to Remove Paint from Brick Using Gels and Paper

When it comes to removing paint off brick surfaces, a two-step approach is one of the most successful options available. When a gel or paste substance is utilized in conjunction with a paper or fiber material, paint removal becomes a far less time-consuming task to do. However, while the Dumond technique is demonstrated here on wood, it also works well on brick. Essentially, you’ll scrape away any peeling paint that may be there before using the remover. Following that, fiber or paper strips are added.

The paint adheres to the fiber, and you carefully pull it away, removing all of the paint along the way.

You might be astonished at how well this works and how it doesn’t cause the brick to become brittle in the process.

Final Thoughts on How to Remove Paint from Brick

When dealing with chemicals, it is essential to wear the proper protective equipment. Protect your eyes, skin, and lungs from injury by wearing the proper PPE. Putting a plastic drop cloth down beneath the work area is also a good idea to keep anything underneath the workspace safe. While a chemical application is most likely the most effective method for this job, it might cause a disposal problem for the rinse water. You’ll have to look into it with your local authorities. In addition, take sure to thoroughly read all of the labels.

You may remove a significant amount of paint by using the suitable chemical stripper and agitating (for example, by using a cordless drill with a fiber brush bit) or scraping the surface properly.

We hope you have gained something from this post.

How to Remove Paint from Brick Fireplace (Tutorial)

It’s possible that you have a gorgeous old brick fireplace hidden below several layers of outdated paint. Taking old paint off of your fireplace and allowing the natural brick to peek through will make your fireplace the focal point of the space. Some people recommend pressure washing to remove paint from a brick fireplace; however, doing so runs the danger of harming the brick or the grout.

There is a more effective approach to remove paint from a brick fireplace. Prior to beginning the process of removing pain from a brick fireplace, you will need to collect a few tools.

  • Bucket, water, phosphate solution, putty knife, and wire brush are all you’ll need. Drop Cloth
  • Personal protective equipment such as goggles and gloves

Step 1: Set up a Drop Cloth

You’ll want to prepare for this by donning your safety goggles and gloves, as well as laying down a drop cloth to protect the floors and walls from any debris that may fall from the ceiling during the installation procedure. Setup will take less time if you take your time, and cleaning will be lot easier after you are through.

Step 2: Use the Stripping Agent

After the paint has been loosening up, you’ll want to apply a phosphate solution or a liquid stripping agent to remove it. At case the product is stronger than you thought, test it in a non-obtrusive location on the fireplace first. After you’ve tested it, you can start applying it to the fireplace and watching the paint loosen up as it does so.

Step 3: Use your Tools to Remove the Paint

Here’s when you’ll want to start scraping the paint off the brick using a putty knife, a wire brush, or another instrument entirely. Keep in mind that the stripping agent should handle the bulk of the hard lifting, and you should take care not to scratch or damage the brick that is beneath the paint when you are working with it. You’ll want to allow the stripping agent to sink in and loosen the paint before proceeding. The solvent should take care of the majority of the work, with your instruments serving mostly to scrape away paint that has already come free.

Step 4: Clean up and Finishing Touches

By now, you should be able to view your brick in its whole. If there is anything that demands particular attention, take care of it right away. It is possible that you will have some difficult locations that will take a bit extra elbow grease to remove the paint. After that, you should be able to clean up your drop cloths and carefully dispose of the stripping agent that you used. The proper disposal of any chemicals should be followed, and you should avoid pouring anything down your drain that might block it (like paint chips).


You’ll want to take your time and be meticulous in your approach to this endeavor. It is unlikely that any of these will cause damage to the fireplace, but if you jam the wire brush or putty knife in at an incorrect angle, you may accidently damage the brick.

Will all the paint come off?

You should be able to remove all of the paint with relative ease. Depending on your skill level, some of it will be easier than others. You might expect to have to apply some elbow grease to some of the more stubborn paint, but if you are patient, you will be able to remove it all.

Should I just use a power washer?

It is not recommended to use a power washer. While it may complete the task, it will create a significant amount of mess, and you run the danger of harming the brick due to the power of the pressure washer’s water. It is far preferable to chip away at it gently with a solution and tools than than using a power washer, which would remove the paint completely off the surface.


A brick fireplace can be the focal point of any room in your house. Unfortunately, it might be buried under some old paint that make it look unsightly. Fortunately, with the right tools and a little elbow grease you can easily remove all that paint and be left with your authentic brick fireplace! If you’ve used our ideas and tactics, drop us a comment and show us your finished off brick fireplaces! We appreciate hearing your success stories, so let us know what worked and didn’t work. Hello, I’m Fred and I enjoy using traditional open fireplaces and wood-burning stoves.

After a while of research, I decided that pellet stoves were the best option for me because they are cleaner than other options on the market.

That’s why created this website – so others can learn about all sorts of fireplace options available to them so they can make an informed decision about what kind will work best in their home too! ABOUT ME PAGE

Leave a Reply

Your email address will not be published.