3 Key Steps to a Concrete Floor Refresh
Photo courtesy of hydetools.com Hyde Tools has provided this material to you. Thank you for visiting. BobVila.com is the source of the information and viewpoints presented. Concrete is one of the most durable building materials available, yet the distinctive drab gray of a concrete slab may appear chilly and unpleasant when used as flooring, especially in low-traffic areas. Lucky for many DIY-inclined homeowners, concrete is also an extremely adaptable material that can be used for a wide range of projects such as house repairs as well as renovations and enhancements.
You can even modify the color and add patterns.
Painting your concrete flooring will give your entire room a new lease on life.
How to Paint a Concrete Floor
Materials and tools are available for purchase on Amazon. –3′′ Extra Heavy Duty Chisel Extension Pole Scraper with a Stainless Steel Blade (available at hydestore.com) •Protective glasses and clothes •Prolonging the length of the pole Gloves that are resistant to chemicals –A solution for degreasing concrete –A solution for removing rust from masonry (if necessary) –A push broom with stiff bristles –MAXXGRIP PRO® 6-3/4′′ Wire Brush made of high carbon steel (available at hydestore.com) –MAXXGRIP PRO® High Carbon Steel 9-Inch Wire Brush –MAXXGRIP PRO® High Carbon Steel 10-Inch Wire Brush (available at hydestore.com) Sprayer with a pump–Vacuum cleaner with wet/dry settings –Crack filler for masonry work –A caulking gun is used for caulking.
–2′′ BLACKSILVER® Putty Knife with a Stiff Blade (available at hydestore.com) –100-grit sandpaper–a roll of clear plastic wrap (optional) –Painter’s masking tape Painting using a 4-Piece Paint Roller Kit from Richard Tools (available at arichard.com) –Additional roller coverings –Paintbrush–Primer for masonry –Epoxy paint for masonry applications –Masonry sealer–BLACKSILVER® PaintbrushRoller Cleaner–BLACKSILVER® PaintbrushRoller Cleaner (available at hydestore.com) –Soap
STEP 1: Prep the Surface
Photo courtesy of hydetools.com Even after your concrete floors have been painted in a different color, the state of the flooring will be obvious through the paint. Lumps, fissures, and other defects that you didn’t address before painting will maintain just enough texture to draw the viewer’s attention to their shadows. That is why you want the concrete floor surface to be as smooth and clean as possible before you begin painting it with a paintbrush.
Get rid of the gunk.
hydetools.com provided the image. It will be possible to see the condition of your concrete flooring even after they have been painted in a different color.
Loose lumps, fissures, and other irregularities that you didn’t address before painting will maintain just enough texture to draw the viewer’s attention to them through their shadows. In order to paint concrete floors, you must first prepare the surface by sanding it down and cleaning it well.
New paint sticks only to a clean, dry surface.
Start with a concrete degreasing product that is appropriate for your flooring (depending on whether they are indoor or external surfaces) in order to get the greatest long-term results with the least amount of peeling. Wear protective glasses, clothes, and gloves when working with concrete degreasing solutions because they are frequently applied to moist concrete. Spray the floor after donning your protective gear.
- It’s easier to use a garden hose to moisten the surface of patio and garage flooring, which can get dry when exposed to the elements. Next, apply the degreaser according to the directions on the package. With a stiff-bristle push broom, scrape the solution into the floor until it is completely removed. Make sure to scrub away any persistent rust spots that have formed by using Hyde Tools’MAXXGRIP PRO® High Carbon Steel 6-3/4′′ Wire Brush (available for $14.24 at hydestore.com), which is made of high-carbon steel and is particularly suited for use on masonry. If you want, you may hold the brush in your hand because of its soft and ergonomic handle, which makes it simple to grip. Alternatively, you can attach the brush to an extension pole so that you don’t have to crouch on your hands and knees when removing huge stains. Despite the fact that you have a floor covered in rust to clean, the tempered carbon-steel bristles will preserve their form. Cleaning interior flooring is a little more difficult since you can’t hose them down like you can with an outdoor hose. In its place, use a pump-type sprayer to wet the concrete with water, then apply the degreasing solution (as directed on the package) and scrub with a push broom to remove any remaining grease. Keep a wet/dry vacuum on available in case there is any surplus liquid. It may be necessary to spray the floor many times, vacuuming up the water between each application, in order to thoroughly remove the degreasing solution.
Finally, fill any cracks that could mar your finished floor.
Concrete filler attaches better to fractures that are free of crumbling concrete, so scrape away any crumbling concrete with a wire brush such as theMAXXGRIP PRO® High Carbon Steel 9′′ Wire Brush (available at hydestore.com for $13.71). Its narrow-angled tip makes it simple for the tempered carbon-steel bristles to reach into cracks and corners, even when the tool is in a tight space. In addition, like Hyde Tools’ threaded wire brush, this one has an ergonomic soft-grip handle that is simple to grab and reduces hand fatigue while working on the job.
Smooth away any extra filler with aBLACKSILVER® 2″ Stiff Putty Knife (available at hydestore.com for $5.41) and, once the filler has dried, softly sand the crack with 100-grit sandpaper to smooth out the surface imperfections.
Receive free, no-obligation quotes from professional painters in your area.
STEP 2: Prime and Paint
Preparing concrete floors with primer before painting them can assist to ensure that your new look will last. Consider using an epoxy paint as a final coat in conjunction with a primer that is suitable with both concrete and the epoxy paint you’re using as a primer. (Epoxy paint is the finest option for flooring that are subjected to a lot of damage.) Epoxy will provide the most lasting effects, and it will outlast latex paint in terms of durability over time.) Make certain that both the primer and the paint are appropriate for the location of your floor, whether it is an interior or an exterior surface, before beginning.
Wait until your concrete floors are dry before you prime.
It is impossible for the primer and paint to adhere correctly if there is moisture on the surface. Placing a small piece of kitchen plastic wrap (about 12″ square) on the surface of the concrete floor is a simple technique to determine whether or not the floor is sufficiently dry. All of the edges should be taped together. Wait for the plastic to dry overnight before inspecting it. Let the concrete dry for another 24 hours before testing it again. If moisture has collected on the bottom of the plastic, repeat the process.
For large projects like this that require a few different applicators, double-check that you haveeverythingyou need.
Stopping in the middle of a project to pick anything up increases the likelihood of paint drying out and leaving obvious brush or roller markings on the walls and ceiling. Consolidating some of your purchases into a single package can help you make sure you don’t forget anything important before you get started—and it can also help you save money on your supplies. In the case of the 4-Piece Paint Roller Kit from Richard Tools, for example, it includes everything you need to roll on the primer and paint: the paint bucket and liner, a cage frame, and a polyester roller cover, among other things.
A bonus is that the threaded cage frame can be attached to a regular extension pole, allowing you to roll on the primer and paint while still standing.
Mask the bottoms of columns, railing posts, or baseboards with painter’s tape before applying any primer.
Using a paintbrush, apply the primer around the floor posts and along the margins of the floor, starting at the center. After you’ve cut in around the edges, you may use a paint roller to apply the remaining primer to the rest of the surface. Take care not to paint yourself into a corner by starting on the side opposite the entrance. Work in thin swaths, about 2 feet wide, to avoid painting yourself into a corner. Maintain a “wet edge” when applying the primer and the paint; in other words, don’t let the swath you’ve just applied to dry before rolling on the next one to avoid streaking.
After the primer coat has completely dried, apply the epoxy paint.
Epoxy paint comes in two parts, and you’ll need to combine the two parts according to the instructions on the label before painting the floor with it. You’ll use the same procedure you used to apply the primer to paint the floor with epoxy paint. Photo courtesy of hydetools.com
STEP 3: Seal the Deal
Although your floor will look fantastic once the epoxy coat has dried (see the instructions for drying time), it is a good idea to seal it to ensure that the effects last for the longest period possible. Choose a sealer that is suitable for use on the outside or interior of your floor (depending on where your floor is located) and that is compatible with the epoxy paint that you have applied.
Heed the manufacturer’s instructions for ventilation, temperature, and humidity.
If you don’t, you run the chance of the product falling apart anywhere from a month to a year down the road. Because of a failure to pay attention to the cure temperature required, many otherwise good-looking projects have been damaged.
Use the same application method you used to apply the primer and paint.
Sealant should be applied around the perimeter of the floor, and then the floor should be rolled. Allow it to dry completely before stepping on it again. Because the sealant will give your floor a beautiful sheen, it will also serve as a strong protective layer and will keep the paint from fading, so your floor will look just as nice five years from now as it does now.
- The majority of primers, sealants, and even epoxy paints available today can be washed off with soap and water alone. Keep a pail of water on available, and wet paintbrushes and roller coverings as soon as they are used to avoid the paint drying on them. In most cases, if you clean the roller cover completely between uses, you may use the same roller cover for both priming and painting concrete floors. When you use the BLACKSILVER® PaintbrushRoller Cleaner from Hyde Tools (available at hydestore.com for $5.14), cleaning a roller cover is a breeze. It has a nylon handle that is simple to hold as well as a curved stainless steel edge that is meant to push paint down and away from the roller. There is a tined edge on one side that looks like it may be used as a comb for extracting even the stickiest painting off brush bristles. Toss off the disposable pan liners, but keep the plastic paint roller pan for future reference. Use a sharp utility blade to cut around the edge of the painter’s tape before peeling it off once the sealant has dried fully. Cutting it makes it easier to remove, and it leaves a beautiful, clean edge on the outside. While cutting, it may be helpful to keep a straightedge parallel to the tape.
Hire a professional to complete the task for you. Receive free, no-obligation quotes from professional painters in your area.
How to Paint Concrete Floors
Every editorial product is chosen on its own merits, while we may be compensated or earn an affiliate commission if you purchase something after clicking on one of our affiliate links. As of the time of writing, the ratings and pricing are correct, and all goods are in stock. Time A busy day of work Complexity BeginnerCosts range from $50 to $120.
Even though we may be rewarded or earn an affiliate commission if you purchase something after clicking on one of our links, every editorial product is chosen independently. When this article was published, the ratings and pricing were accurate, and all goods were in stock. Time A full day’s worth of activities Complexity $50 to $120 for a beginner
- Crack sealant for concrete
- Concrete paint
- Painter’s tape
- Crack sealant for concrete
Project step-by-step (7)
- There are a plethora of concrete floor paint alternatives available on the market today. No matter if you’re painting your garage floor, basement floor, or even your front stoop, knowing what kind of paint to buy is essential
- Basement flooring are a good candidate for Drylok Concrete Floor Paint. Because it is latex-based, it is durable enough to be used in high-traffic locations. In addition, you may paint over previously painted floors without the requirement for a priming coat to protect them. This paint dries quickly, has a mild odor, and can be cleaned off with soap and water. Rust-Epoxy Oleum’s Shield Basement Floor Coating Kit, which is available in a variety of colors and a white foundation for custom tinting, may help transform your basement into a usable living area. This two-part water-based epoxy may be applied in a single layer without the requirement for a priming. The package contains two cans (one quart activator and one gallon base paint) as well as decorative chips for texture. Kilz ConcreteGarage Floor Paint is a one-part interior/outdoor water-based floor paint that is suitable for both interior and exterior use. It may be applied in a single coat to concrete, masonry, stone, and brick surfaces, making it ideal for high-traffic areas such as walkways and garage floors. In two hours, it is dry to the touch. In four hours, recoat the surface.
Prep Painting Area
- Remove any obstructions from the painting area and totally clear it. Make a visual inspection of the concrete for cracks, structural deterioration, chipped paint, and other foreign objects such as dirt, water, and grease. Concrete cracks can be used to fill any cracks. Seal any structural damage with a sealant and repair it using hydraulic cement or quick-setting cement. Before painting, check to see that the cement is completely dry. Depending on how many times the floor has been painted, you may wish to remove the old paint with a wire brush or a side grinder fitted with a wire wheel attachment. Clean the painting area thoroughly with a broom and vacuum
Sign Up For Our Newsletter
Complete your do-it-yourself tasks like an expert! Become a subscriber to our newsletter! Do It Right the First Time, and Do It Yourself! Step number three.
- Painter’s tape can be used to mask off the walls and baseboards around the perimeter of a room before painting. Mask off any moldings, banisters, and baseboard heaters that you don’t want to have paint all over them.
- At this stage, it may be essential to apply a coat of primer to the surface. Some floor paints don’t require the use of a primer at all. Make sure you follow the manufacturer’s recommendations and follow the application directions on the paint container
- DryLoc floor paint is a type of floor paint that dries quickly. It is recommended that the initial coat be diluted with one pint of water for every gallon of paint used. Allow at least four hours between coats once the first coat has dried
- Perhaps at this stage you will need to apply another layer of primer. It is possible to use floor paint without priming it. Make sure you follow the manufacturer’s recommendations and follow the application directions on the paint container. Floor paint using DryLoc technology A pint of water per gallon of paint is suggested for the initial coat, according to the manufacturer. Allow at least four hours between coats once the first coat has dried.
- Before you begin, swirl the paint with a paint stick to ensure that it is evenly distributed. Begin in the farthest corner of the room from the door, in the corner closest to the door. Working in three- to four-foot portions, begin painting from the center and work your way out. Make certain that you do not paint yourself into a corner. Fill the roller tray just a little bit more than halfway with paint. If there is too much paint in the tray, it may overflow. Fill the roller with paint from the paint tray and roll the paint across the floor to cover the whole surface. Roll the roller straight back over the paint without reloading it to ensure that the floor is uniformly coated with paint. Fill the roller with paint once again and begin a fresh row, this time overlapping the previous one. The edges of the roller have a tendency to leave paint build-up lines on the surface of the paint. Roll the paint back over the lines to make them blend in with the rest of the painting
- Before you begin, swirl the paint with a paint stick to ensure that it is evenly distributed
- To begin, locate the farthest corner of the room from the entrance. Paint in three- to four-foot portions, working your way outward. Make sure you don’t put yourself in a bind. Over half of the paint should be placed in the roller tray. It is possible that too much paint will flow out of the tray. Fill the roller with paint from the paint tray and roll the paint across the floor to create a patterned effect. For a uniformly painted floor, roll the roller back and forth over the paint without reloading the roller. Fill the roller with paint once again, then begin a new row by overlapping the previous one with the preceding row. In most cases, paint build-up lines are left by the edges of the roller. Roll the paint back over the lines to make them blend in with the rest of the painting.
How To Paint a Concrete Floor
As soon as Ruby and Bill had settled into their new lake cottage, we set out to do a number of jobs, one of which was to paint the concrete floor in their basement. It’s a spacious walk-out basement with plenty of natural light. They opted not to spend the money on laminate flooring down there (it was going to cost $3K! ), but I suggested that they paint the concrete as I did in my laundry room, which would make the area seem extremely fresh and clean. They agreed. They worked on cleaning up the concrete dust with a shop vac and also cleaned the floors a few times to ensure that all dust and debris was removed from the flooring before we began.
- If you are working on a fresh new concrete floor, make sure to sweep it well.
- I just cleaned and mopped the floor in my laundry room in order to remove as much filth as I possibly could before starting to paint.
- It came out just stunning!
- Tony Taupe is the color.
- My painted concrete floors, on the other hand, have been a complete success.
If you want to paint the concrete floor of your garage, I would consult with a professional to determine which product would be the most effective. There are other treatments available that are more durable than this porch concrete paint, so I’m not sure whether it would work for a garage.
How To Paint a Concrete Floor:
One of the jobs we had planned for after Ruby and Bill had moved into their new lake cottage was to paint the concrete floor in their basement. We were looking forward to this opportunity. You have plenty of natural light in this walk-out basement. After much deliberation, they chose not to spend the money on laminate flooring down there (it was going to cost $3K!). However, I advised her that painting the concrete as I did in my laundry room would make that space seem extremely fresh and clean.
- This technique necessitates a completely clean surface, so if you are working on a fresh new concrete floor, make sure to vacuum off as much dust as possible before beginning.
- I just cleaned and mopped the floor in my laundry room in order to remove as much filth as I possibly could before starting to paint the walls and ceiling.
- For those of you who missed it, check out this post from when I was renovating my laundry room, in which I showed you how I painted the floor in bright stripes with the same Porch and Floor paint.
- For this job, we utilized Sherwin Williams Concrete floor paint, which was finished with H C glossy clear topcoat, to provide a durable surface.
- I utilized this method in my laundry room, and it was really effective in finishing it.
- If you want to paint the concrete floor of your garage, I would consult with a professional to determine which product would be the most effective for you.
Decorated Life is entirely financed by its readers. If you make a purchase after clicking on one of our affiliate links, we may receive a commission. Read on to find out more Contributed by: Decorated Life Team| If you take the time to prepare your concrete floors, apply a speciality concrete floor paint that is specifically designed for your concrete floor, and add a wonderful design, your painted concrete floors may look really stunning. It appears to be difficult, yet it is less difficult than you may believe.
- This is a lengthy post, so make yourself a cup of coffee and relax, or simply scroll down to the portion that interests you.
- Garage, basement, living room, patio, or balcony painted concrete floors are a terrific addition to any floor in your home.
- You may paint over it with regular paint, but it will peel off after a few months.
- She is a multi-talented woman.
- In order to elevate this appearance to a higher level, there are several things you can do.
- Another option is to apply a stencil over the top of the paint.
- Source:Houzz This simple floor design was constructed with painter’s tape and may be seen in our short movie below.
Consider a checkerboard pattern in white and gray, or a black and white pattern, or even stripes. It is a timeless evergreen appearance that may be used to instantly improve your curb appeal.
Painted Concrete Floor Designs
It is the readers who make Decorated Life what it is today. It is possible that we will receive an affiliate commission if you make a purchase after clicking on one of the links on our site. Obtaining Additional Information | Created by the Decorated Life Team Preparation, use of a speciality concrete floor paint, application of a beautiful design, and sealing the surface with a concrete floor sealer may make painted concrete floors seem amazing. However, it is not as difficult as you may expect to complete.
- Given that this is a lengthy article, either get yourself a cup of coffee and relax, or simply scroll to the section that interests you.
- Garage, basement, living room, patio, or balcony painted concrete floors are a terrific addition to any floor in your house.
- You can paint over it with regular paint, but it will come off in a matter of weeks.
- Obtainable from: She Is Superwoman However, while painting your floor with a single solid color may be the quickest method, it may frequently appear flat and uninteresting.
- The use of a stencil over the top is an additional option.
- Source:Houzz Painter’s tape was used to swiftly construct the floor pattern in the short film below.
- With its classic evergreen appearance, it is a quick and easy way to enhance your curb appeal.
How To Paint Concrete Floors
In case you are a fan of enormous designs, the white floor with a giant black coffee design below may be of interest to you. Because of the striking contrast in hues, you are drawn to the floor pattern. It is out of character with the rest of the space, but it does create the impression of carpeting or tiles. Pinterest is the source of this image. The stenciled concrete floor above is the polar opposite of the previous color scheme; it is a very dark coffee or black floor with a white stencil on top that looks like carpet or tiles.
Painted Concrete Floors – The Healthy Option
There are additional health benefits to switching from unpainted flooring to painted floors, including the elimination or management of allergens. If allergies are a problem for you or your family, it may be time to pull up your carpets and consider painting your floors rather than carpeting. Allergens breed in carpet fibers, and removing carpets eliminates their breeding grounds, hence reducing allergies. Concrete floors are also an excellent anti-slip flooring alternative, as being anti-slip implies putting safety first in any situation.
My Paradissi is the source of this information. There are several decorative concrete professionals that can assist you with either the preparation of your floors or the completion of the work entirely if you feel the procedure to be above your DIY capabilities, but they are not inexpensive.
Concrete Floor Preparation
- Remove any old carpeting, tiles, or vinyl flooring. Examine the condition of the floor. You’ll be surprised at how much filth has accumulated under your carpets over time. Put on a mask and vacuum or sweep while doing so. Using a crowbar or a nail puller, remove the nails from the flooring. Slow down in order to prevent removing large pieces of concrete
- To remove stubborn dirt or carpet adhesive remnants, dilute a hydrochloric acid solution with 4 parts water and use it as a spot cleaner. There are concrete etching products available, such as Rust-Oleum 238475 EPOXYShield Concrete Etch. Working in a well-ventilated room with protective eyewear and gloves is recommended. Using a harsher cleaner and a specific floor cleaner/buffer to remove extra layers of residue from your floor is recommended if your floor is in bad condition. These are large machines that can be expensive to rent, but they are far less expensive than hiring a person. If it appears that you may want assistance, contact a competent decorative concrete contractor. Concrete patch should be used to repair any holes. When creating a weathered rustic or industrial aesthetic, it is best to leave the holes in place. Vacuum or sweep the floor once again
- Floor cleaner should be used to remove residue, filth, and loose particles from the floor
- The cost of concrete floor paint is more than that of wall paint, but it is also more durable and long-lasting than wall paint. If possible, use a spray gun. In comparison to a paint brush, they are both speedier and use less paint. Many people believe an HLVP spray gun to be the greatest hvlp spray gun available. Because the pressure is decreased, it results in a softer finish overall. It is also simpler to use for beginners, and it reduces the amount of overspray paint wasted.
10 Tips forPainting Concrete Floors
- Remove any glue, nails, or concrete irregularities that may have formed. Sandpaper is quite effective in removing adhesive. Concrete must be absolutely clean and dry before it can be used. Within 1-5 days, use a humidifier to remove excess moisture from the air. Only concrete floor paint should be used. Two coats of concrete primer should be applied to your flooring. This forms a bond with the concrete, allowing the topcoat to adhere to it. Allow for a 24-hour drying period after applying the primer. Apply the epoxy to the surface. Start with a little paintbrush and work your way around the edge. Continue to paint in the same manner. Work your way away from the entrance using a sheep’s wool roller on a poll
- It will take at least 12 hours for your first application of concrete floor paint to cure. Apply a second coat of concrete floor paint and epoxy paint to the concrete floor
- Wait seven days before walking on painted concrete floors with shoes or putting furniture on them to avoid the possibility of scratching the surface. Regardless of what the paint container claims, the primer will prolong the drying process by several hours. To repair scratches on painted concrete floors, use concrete floor paint and epoxy paint to patch them up.
Painting Concrete Floors Finishes
Painting concrete floors with solid colors, borders, or stencils is a terrific way to make a statement. Acid etching solutions or stains have a distinct appearance, and they require more time and talent to totally convert your flooring. Stains and etching solutions react with the concrete to produce patterns, while etching solutions are absorbed into the concrete. Not all concrete floors are appropriate for staining or are capable of absorbing stain. If you plan on staining your concrete, you should test it first by saturating it with some water.
- If the water condenses on the surface of the concrete, you may need to rethink your alternatives.
- The use of a dark stain gives the appearance of stone.
- Allow time for drying.
- The sealer is applied with a brush or a roller to the dry surface once it has dried.
- Using epoxy paint on concrete floors to create a beautiful concrete floor is demonstrated in this short video clip.
- If you want the greatest results, choose a high-quality product like Valspar 1534 Porch and Floor Latex.
- What do you think about making your own flooring out of paint on concrete, similar to the painted floor boards seen below?
Painting Concrete – Concrete Floor Rugs
If you want to create an elaborate pattern on a concrete floor rug, you may go large or tiny with your painting. If you don’t want to wait or spend money on a stencil and would rather make your own, here’s a guide on how to make your own stencils: how to make stencils. Pinterest is the source of this image. This ‘rug’ look is particularly well suited to kitchens and bathrooms. They provide color as well as the appearance of texture. They also require less time and money to complete than a full floor painting project.
Pinterest is the source of this image.
How to Stain Concrete Floors
This tinted concrete floor has the appearance of a ceramic tiled floor. The floor remains cool in the summer and is simple to clean with a mop. Pinterest is the source of this image. Concrete floor staining is not a task for the faint of heart. The material costs for the level above were around $500, but it was a time-consuming project. More photographs may be seen here. Instead of painting concrete stained floors, stains should be used.
The results you achieve depend on whether you use full strength or diluted stains, as well as if you use various stains to create a marbling, granite, or stone effect on the surface. At all times, adhere to the given directions. Observations on this floor include the following:
- It will last for a very long time. It is simple to maintain by wiping on wax every 6 months in heavy usage areas
- It is also inexpensive. Use 1/2′′ masking tape to form the lines, and then spray the stain over the top. When the painters tape is removed, the natural color of the concrete may be seen through. This is an acid stain that reacts with the concrete in a direct manner. After the stain has been put, a layer of urethane sealer is applied, followed by a coat of wax. The effect seen above was created with a single brown stain tint. The dark portions are at their maximum power. Luminous parts are diluted with water 1:1
- Lighter areas are diluted with water 2:1
Whether you paint a concrete floor rug, stain it, or use an etching solution, whether you do it yourself or hire a decorative concrete contractor, the end effects of painted concrete or stained concrete may be amazing, giving your house a genuinely one-of-a-kind feeling and appearance.
How To Paint Concrete UPDATED! (Plus My Secret Cleaning Tip!)
Friends, have a wonderful Monday! You may or may not be aware that around a year and a half ago, I published a comprehensive lesson on how to paint concrete and cement. Ivie’s floor was my first experience, and it has kept up very well; in fact, it has held up so well that I have chosen to remove the carpet from Dylan’s room and paint her floor as well. So what’s the point of another tutorial? But I’ve learned a few things along the road that I’d like you to be aware of in case you decide to take on your own concrete painting job in the near future.
- That is without a doubt not the most enjoyable profession in the world.
- (The bits of wood along the edge of your carpet that keep it in place are known as edging.) This may be accomplished using a variety of instruments, ranging from a chisel to a hammer to a screw driver.
- Essentially, you’re using them to pry the tack strips up from the bottom.
- Adhesive should be removed.
- The correct wording of that phrase is Carpet Human Fly Trap, which is a contraction of the words carpet and human.
- Four years after we moved into our home, the carpet adhesive was still quite sticky, indicating that it had not dried properly.
- As I mentioned in my original article, I recommended dousing it with Lacquer Thinner and allowing it to set for a few minutes before re-dousing it and scraping it off with a plastic scraper.
There is very little scraping required.
Fill in the Gaps For those of you who had carpet in your home previously, you will have a lot of charming small holes along your baseboard that will need to be repaired before you can start painting.
Allow it to set overnight before using it again.
Using a pole sander (which can be purchased for roughly $6.00 at Sherwin Williams) and 80 Grit Sand Paper, rough up the whole surface of the floor, starting with the edges.
Then sand it in the opposite direction, and finally sweep it away.
Continue until you are certain that there is no dust remaining.
(If you get it wet at this stage, you will have to wait 24 hours for it to properly dry, so avoid doing so.) Special attention should be paid to the edges where the tack strip holes were filled, and they should flow seamlessly into the surrounding area.
Paint Painting a floor is, by far, the simplest thing on the face of the world.
You don’t even need a paint tray for this project!
This job will not be completed with regular latex paint.
Herwin Williams Porch and Floor Enamel is the paint that I recommend for this project.
There are no wild fumes because it is a water-based paint that is self-priming and glides on quite smoothly.
), you don’t want to end up with the wrong product.
Check to see that you’re using a microfiber roller cover with a 5/16″ nap if you want a truly smooth finish.
I normally pour a portion the size of a dinner plate into the container.
Roll it in the same manner as you would a wall, in the shape of a “W” pattern.
So make sure to go over them again and again.
Allow coat 1 to cure for a few hours.
The floor in Dylan’s room only required two coats, but if you find yourself in this situation, wait the right amount of time before recoating.
Porch and Floor Enamel does not require the application of a top coat in order to be sealed.
It makes them look shinier (as seen by this photograph taken in Ivie’s room!).
It is H C Wet Look Concrete Sealer that I recommend as a top coat (you can also buy this at Sherwin Williams).
When your life turns yellow, you will despise it.
To eliminate this potential problem, I would simply recommend that you single coat it.
Surprisingly, the most effective solution that I have discovered (after experimenting with other options) is dish soap and a washcloth.
Apply a tiny quantity to the troublesome area.
It should be cleaned up with a clean, non-soapy cloth.
Please post your questions in the comments section and I will respond there! This post was written in collaboration with Sherwin Williams. All opinions are my own. Unless otherwise stated, all project ideas, thoughts, and hard work are entirely mine.
5 Mistakes to Avoid when Painting Concrete Flooring
It is possible to boost the durability and longevity of your concrete floors while also changing the appearance of your area by painting and sealing them. However, this process entails more than merely splattering paint on your flooring and hoping for the best; there is more to it than that. Successfully painting a concrete floor needs extensive preparation, ample supplies, right technique, and other factors. Read on for more information. In light of these considerations, it is typically preferable to simply engage specialists who are experienced in concrete floor painting.
Consequently, here are five common errors to avoid while painting concrete flooring.
What Not to Do When Painting Concrete Floors
As we’ve covered in several past posts, surface preparation is at least half of the fight when it comes to painting a surface, and this is especially true when it comes to painting a concrete floor. Considering the porous nature of concrete, concrete floor preparation for polyurea coatings is especially important. Dirt, dust, debris (including moisture), and other contaminants can easily enter the pores and cracks of bare concrete, and pressure from above and below your floors can cause fracturing, pitting or spalling.
As a result, before to painting, make sure you do all of the essential preparation work, which includes:
- Clearing the area
- Sweeping and washing the floor
- Scraping and sanding away old paint
- Vacuuming up remaining dirt
- Filling in cracks and gaps
- And Preparing your flooring with primer
The purpose of this preparation job is to provide a smooth, clean, and responsive surface for the next floor paint.
2. Painting in a Suboptimal Environment
After you’ve completed the preparation of the floor itself, you’ll want to focus on preparing the surrounding environment in order to produce the best possible conditions for application and curing. Depending on whether the environment is too humid, excessively dry, excessively hot, or excessively cold, you may have problems at various stages of the procedure and end up with subpar results. It is possible that different types of coatings will have slightly different recommendations in this regard; however, in general, your floor should maintain a minimum temperature of 55 degrees Fahrenheit and the surrounding air temperature should be between 60 and 85 degrees Fahrenheit for the best results.
It may be necessary to install humidifiers or dehumidifiers (depending on your climate circumstances) as well as discover techniques to modify the temperature if your climate conditions are significantly different from these (if indoors).
3. Choosing the Wrong Product for Your Application
With so many various brands and variants of concrete paints available on the market, it can be tough to determine which one is the best fit for your requirements. At the absolute least, ensure that your product is intended for external or interior usage, depending on the location of your concrete – outside concrete floor paint tends to include a higher concentration of volatile organic compounds (VOCs), which may be harmful to your health if breathed.
So, if you’re painting inside, make sure to use a zero- or low-VOCindoor epoxy floor paint to reduce the danger of exposure to volatile organic compounds. In these cases, the more research you conduct, the more assured you will be in your conclusion.
4. Lacking the Necessary Amount of Coverage
As is the case with painting any surface, you want to make sure you purchase enough product to cover the whole surface with a protective layer that is level and complete. You may find yourself stretching out the epoxy to make up for a shortage of product if you underestimate the amount of product you need. This will result in a less glossy surface and a poorer coating in general. Prepare your floor by taking exact measurements of its surface area and carefully reviewing the coverage rate of the floor sealing goods you intend to purchase in order to prevent making this error.
5. Not Giving Your Floors Enough Time to Cure and Dry
Following your successful painting of concrete floors, you may believe that the task is over. This is not necessarily true. Although you should exercise caution around your flooring to ensure that the coating cures and dries correctly, it is not necessary. This area should be avoided for a few days after the epoxy concrete floor paint has been applied since it can take up to 48 hours to completely cure. Failure to allow the coating to rest properly may result in contamination of the surface and/or smudging of the topcoat.
Afraid of Messing Up Your Floors?
The satisfaction of painting your concrete floors on your own can be gratifying, but no one claimed it was simple. If you aren’t sure in your DIY talents, Anderson Painting specializes in the application of Penntek polyurea coatings to any and all concrete surfaces, including poured concrete. Call us at 919-610-1855 or send us an email at [email protected] to learn more about us and what we do!
Concrete Floor Paint Colors – Indoor and Outdoor IDEAS with PHOTOS
When I initially decided to paint my basement flooring, I assumed that the only color option available to me was slate gray. However, I was wrong. It was a thrilling experience to finally get rid of the oil stains and rubber markings on my floors. I was disappointed, though, to discover that I would only be able to change the hue from one shade of gray to another in the end. The first time I walked into my neighborhood hardware shop, I was greeted with a nice surprise. It was possible to get concrete paint in a wide variety of hues.
During my conversation with the store clerk, I discovered that there are various procedures for creating decorative paint patterns.
When I came home, I was energized by the newfound information I had acquired.
I couldn’t be more pleased with the outcome!
|Best Durable Paint|| Rust-Oleum Decorative Concrete Coating
|Best Concrete Floor Paint (Multicoloured)|| Drylok Concrete Floor Paint (Multicoloured)
|Water-Resistant Paint|| BEHR PREMIUM ConcreteGarage Floor Paint
|Excellent for Floors and Walls|| Surecrete Concrete Floor Paint Colors
|Best Price|| KILZ Over Armor Textured Wood/Concrete Coating
Drylok Concrete Floor Paint (Multi-Colored)
Drylok was one of the first concrete coatings that was recommended to me. This long-lasting concrete paint is available in eight pre-mixed hues. Georgetown Gray, Dover Gray, Soft Gray, and Gull are the smokiest hues available from Drylok. I’ve arranged them in descending sequence of darkness to lightness. The fact remains that Georgetown Gray has more cool blue undertones than the other two selections, which is worth pointing out. Drylok also produces two light brown paint shades, both of which are available online.
Two red concrete paints are also available from the paint producer.
Drylok also manufactures a flat white base paint in addition to its eight pre-mixed colors.
Thus, virtually any hue in the spectrum is available to you!
Rust-Oleum Concrete Floor Paint Colors
Rust-Oleum is yet another paint producer that offers a wide variety of paint colors for purchase. ConcreteGarage Floor Paint from Rust-Oleum is available in three pre-mixed colors. Battleship Gray Satin is the company’s darkest paint hue, and it is available in a variety of finishes. They also have a lighter Armor Gray Satin that is available. Furthermore, they provide a beige paint called Sand Satin, which is a beige color. Gray paint is offered in 1-gallon and 5-gallon cans, respectively. Sand Satin, on the other hand, is only available in 1-gallon cans.
BEHR PREMIUM ConcreteGarage Floor Paint
Colors for concrete and garage floors are also available from Behr, which also manufactures a large selection of them. One can get a preview of 75 various hues from the company’s color pallet. These colours, like those of the previously listed manufacturers, include a varied range of cool and hot colors in various shades. A lot of them are various tones of brick red, beige, brown, blue, and gray, among other colors. Colors like yellows and greens that are more muted have been used into the design.
Behr also manufactures a decorative finish that can be placed over concrete paint, which is available in a variety of colors.
Granite Grip’s hues are motivated by the colors seen in real stones.
Surecrete Concrete Floor Paint Colors
Surecrete is another another epoxy for concrete floors that is widely used. It is available in 30 common hues, which include grays, reds, browns, tans, and blues, among others. It’s also available in two more colors: black and white. Additionally, the basic color of your choice can be tinted to meet your specific needs. With concrete paint’s bespoke color possibilities, there are no limits to what you can do with it.
Kilz Concrete Floor Paint Colors
Yet another popular epoxy for concrete floors is Surecrete. Grey, red, brown, tan, and blue are among the 30 regular hues available, with gray being the most popular choice. Also available in black and white, this item is versatile. Additionally, the base color of your choice can be tinted to match. You can do anything you want with concrete paint since you can mix your own colors.
Trendy Color Options
When I learned that I had more color possibilities besides slate gray, I went to Pinterest to get some inspiration. I was interested in seeing which painting methods were popular at the time. I discovered a plethora of photographs of single-color base coats. However, I came discovered a number of multi-colored paint patterns as well. Many amateur painters were experimenting with a wide range of paint colors in order to produce striking new appearances. Faux bricks, faux slate, faux wood, and ornate stencils were some of the most popular choices.
Interior Concrete Paint Color Ideas
Take some time to consider your design objectives before deciding on a paint color for your internal concrete floor. Indoor rooms are often exposed to less light than outside settings. As a result, softer tones of paint are frequently selected in these types of rooms. Concrete paints, as opposed to concrete stains, provide a homogenous covering on the concrete surface. They also act as a protective barrier, shielding the skin from moisture, heat, and high pressure.
Exterior Concrete Paint Color Ideas
Dark colors are often selected for outdoor concrete paint treatments since they are less reflective. Colors with dark bases are less prone to fade or discolor than those with lighter bases. Aside from that, they are more effective at hiding imperfections, which are more prone to occur in outdoor settings. Deep grays and burnt oranges are the colors of choice for most homeowners. Patios and driveways made of terra cotta, brick, and slate are popular choices among homeowners. Lighter hues, on the other hand, retain their cooling properties.
Tips on Sifting Through Color Choices
There are many different colors of concrete paint to choose from. How can you narrow it down to just one? Choosing a hue that complements any existent architectural aspects is something I would suggest you do. Take note of the color of your house, including the trim, walls, roof, and patio. Select a color that is complementary to the elements you have chosen. Furthermore, consider the impact that the color of your concrete floor will have on the value of your property. All buyers will not be drawn to the more daring and dramatic alternatives available.
Neutrals allow you to easily switch up the look of your home.
The color of your paint will be a permanent fixture in your home for a long time.
Moreover, go through home and garden journals to get the ideal color palette for your space.
Colors that are coordinated together produce instant harmony.
Paint producers create color palette guides and paint chips that are based on the work of professional designers.
PRO TIP: When selecting a floor color, it is important to consider the overall design of the space.
Is there a lot of light in the room?
What kind of décor do you have in mind for the room?
Because, after all, the color you pick will have a long-lasting influence on the appearance and feel of your house.
Dark hues, on the other hand, are frequently used to generate drama.
Using Paint Colors to Create Artistic Effects
You may use a variety of paint colors to make visually attractive creative masterpieces with ease. Concrete paint may be used in a variety of ways, from mixing to marbling. You may also achieve the look of concrete stain without having to spend a fortune on these expensive procedures. Concrete paint patterns with white mandalas stenciled on top of a dark gray base coat are among my personal favorites. In a recently remodeled kitchen, this paint work was the center point. It’s an excellent demonstration of how a fresh coat of paint can totally change a living environment.
Concrete paint drastically changes the appearance of cement flooring. There are no limits to the looks you may design because there are an infinite number of color selections to pick from. Whether you choose a simple gray or a deep purple, the paint will preserve your concrete while also increasing the overall appearance of the surface. Almost immediately after transforming my discolored gray floor into a shimmering copper surface, I began receiving praises. In the comments box below, please share your favorite concrete floor paint color ideas with us.