How To Paint Fireplace Brick Interior

How to Paint a Brick Fireplace

It has been on my to-do list for months now, and today’s topic is all about how to paint a brick fireplace, which is exactly what I’ll be covering. That’s right, you read that correctly. That day has finally arrived, after much anticipation for more than a year. I have finished painting the massive fireplace in our living room. I’d been putting it off for a long time, partly because I anticipated it would be a major hassle and take several days to finish. But I’m pleased to report that it wasn’t quite as difficult as I had anticipated.

This content is brought to you by KILZ.

What Supplies Will Be Required:

  • The following products are used: KILZ Latex Interior/Exterior Primer
  • 3/4′′ High-Density Polyester Roller Cover
  • Behr Masonry, Stucco, and Brick paint
  • And Behr Masonry, Stucco, and Brick paint.

1. DISINFECT THE BRICK The initial stage in the process is to thoroughly clean the brick’s surface area. Before you begin painting, you just want to make certain that the surface is clear of dust and grime. Our brick was already rather clean, so I just wiped it down with a moist towel to remove any dust and grime that had collected. If your fireplace is really unclean, you may also use a wire brush and a heavy-duty cleanser to clean it. 2. PREPARE THE BRICK WORK Following that, it’s PRIME, PRIME, PRIME!

  1. In this case, I used KILZ Latex Interior/Exterior Primer, which serves as a primer, sealant, and stainblocker all in one product.
  2. Furthermore, because it is highly pigmented, it provided excellent coverage over the yellow brick and black grout lines.
  3. Furthermore, because it is water-based, cleanup was really simple.
  4. It has a greater capacity for holding paint and has made the painting procedure a snap.
  5. It took me approximately an hour to paint the entire fireplace with primer, and one coat was enough to achieve the desired results.
  6. Here’s a close-up of the surface after one layer of KILZ primer.
  7. It produced a great smooth surface that was ready for painting!

COAT THE BRICK WITH PAINT Following the application of the KILZ primer, I painted the masonry with Behr Masonry, Stucco, and Brick Paint in white.

Fortunately, I just required one coat of paint to complete the project.

This significantly increases the amount of light in the room.

The yellow brick was just out of date; it had clearly not been altered since the house was constructed in the 1980s.

It’s time to do the happy dance.

After months of feeling scared by this project and the prospect of painting brick, it turns out that it isn’t quite as tough as I had anticipated.

That’s all.

I’m overjoyed with how this project turned out, and I’m delighted that it’s finally finished. It feels incredible to have completed this task and cross it off my extensive to-do list. On to the next job, please!

GO HERE TO GET MY 10 BEST CHALK PAINTING TIPSTRICKS!

Thank you so much for dropping here, and please do not hesitate to contact me if you have any questions. And, as usual, you can find me expressing my thoughts on social media sites such as Facebook, Instagram, and Pinterest.

How to Paint a Brick Fireplace (and the Best Paint to Use!)

Brick fireplaces may be a stunning decorative feature in a home. I adore ancient brick, especially when it can be found in old farm kitchens or poking out from behind crumbling plaster. Brick, on the other hand, may sometimes feel gloomy and weighty. Our farmhouse dining room was certainly like this, and it needed to go. Our dining area was completely changed when we painted the brick fireplace! Here, I’ll show you how to paint brick and give a collection of 10 or more examples of painted brick fireplaces.

What’s the Best Paint to use when painting a brick fireplace?

I used to live in the “big city,” as they say, and would constantly go to a large box shop to buy paint when the mood struck. Although there is nothing wrong with those establishments, I like our neighborhood hardware shop. Despite the fact that the variety is fewer, the workers are far more competent when it comes to providing answers. After conducting some online research, I anticipated ordering a masonry, brick, and stucco paint; however, the paint technician advised me otherwise. He advised a can of Zinnser Primer, which was tinted to match the color of the paint, as an alternative.

  1. My go-to paint is Porter Paints Hi Hide, and I picked a Semi-Gloss finish so that it would be easy to clean as is my customary practice.
  2. All I’d heard about brick was how much it absorbed the color it was painted on.
  3. However, this particular color combination proved out to be really effective.
  4. Let’s just say the evidence is in the pudding photographs (haha!) and that’s it.

How to Paint Brick

If you’d like to download and print these instructions (which also contain links to the necessary items), simply click here to go directly to the instruction sheet.

Supply List

  • Paintbrushes, high nap rollers ideal for tough surfaces, tinted primer, and semi-gloss paint are also available.

Instruction

1. Vacuum and clean the brick fireplace to remove any dirt, cobwebs, or dust bunnies that have accumulated. 2. Gather all of your materials. A tinted primer will be used for the first and second applications. 3. Paint the mortar between the bricks with a brush to give it a more finished look. 4. After the primer has been applied to the mortar, paint the face of the brick with the same color as the mortar. To apply the primer, you may use either a brush or a high nap roller that is suited for use on tough surfaces.

  1. By the end of this second application, the brick should be nearly completely covered with paint.
  2. After the second layer of paint has dried, add a semi-gloss finish to the surface.
  3. It’s hard to believe how much coverage there is with only one coat of semi-gloss paint.
  4. My expectations were that I would be painting at the very least one coat of priming and three coats of paint.

I also anticipated it to be time-consuming. When you get high-quality paint, on the other hand, it makes all the difference. This combination applied smoothly, had a smooth semi-gloss finish, and provided excellent coverage.

TipsTricks

  • Spending a lot of money on a fine brush is not necessary! Brush bristles will have a difficult time dealing with the hard brick texture. I prefer to get inexpensive multi-size paintbrushpacks that may be used for a job and then thrown away once it is completed. Make certain that you have done your homework. Cover the area surrounding the hearth with newspaper and tape the fireplace doors and insert

FAQs: Painting a Brick Fireplace

What color paint did you use for this project? Because it is a bespoke blend to match the wood trim in our home, it is not available. The following are the specifics of the formula: Light Base Porter Paint Hi Hide Interior Latex (PP109) Porter Paint Hi Hide Interior Latex B=3, C=15, and F=1 What is the durability of the paint? After three years, there is just one location on the hearth where the paint has peeled away. Because we have small children, the fireplace is frequently utilized for play, leaping, slamming toys, and other activities.

  1. In the majority of situations, no.
  2. If there is a significant quantity of soot around the firebox or hearth, you may need to wash the brick prior to painting it to remove it.
  3. Does it matter if I use the same color scheme in the firebox?
  4. If it is intended to be used as a fireplace, you must choose a paint that is built to withstand high temperatures in the fireplace.

Instructions

  1. Clean and dust the brick fireplace using a vacuum. Make certain that all trash, cobwebs, and dust have been removed
  2. Paint the mortar with a colored primer, applied with a paintbrush. After the primer has been applied to the mortar, apply primer to the face of each brick. When working on difficult surfaces, use a high nap roller developed for this purpose. Re-apply a second layer of colored primer when the first coat has dried, following the same procedure as in step 2. Once the second layer has dried, use a paintbrush to paint the mortar lines with a semi-gloss paint. Finally, paint the face of each brick with a semi-gloss paint to complete the project. When working on difficult surfaces, use a high nap roller developed for this purpose.

Brick Fireplace Makeover

Now it’s simply a matter of sitting back and enjoying it. Of course, this is the most enjoyable part! Consider going back to the beginning of the story. The walls and fireplace have been freshly painted, the drapes have been replaced, and there is a Sputnik light in the room. as well as a restored dining room, which we are well on our way to accomplishing Wouldn’t you agree it’s been quite a transformation? You might also be interested in: Makeover of a Farmhouse Dining Room on a Budget

10+ More Painted Brick Fireplace Makeovers

If this endeavor wasn’t enough to persuade you to paint your brick fireplace, these painted fireplace makeoverswill certainly enable you to make up your mind about it. Your room may be overshadowed by dark brick, making it appear depressing. Consider painting it a bright white color to liven it up. Alternatively, you might be interested in:How toBrighten a Dark Room(the Ultimate Guide!) Would you want to bring a little drama into a drab room? A gallon of gray paint may be used to draw attention to a brick fireplace while also adding contrast to the area.

Modern Gray Brick Fireplace

The use of gray paint on the brick, black paint on the hardware, and a DIY mantel alter a 1970s brick fireplace. Photo courtesy of Schneiderman’s.

If you liked this DIY project, you might also like:

  • Instructions for Installing a Faux Brick Backsplash
  • Learn how to German Schmear Brick (Mortar Wash Fireplace) in this video. Photographs of German Schmear fireplaces before and after restoration

How to Paint Your Home and the Interior Brick Fireplace

When painting the interior of your fireplace, it’s vital to examine a number of different aspects before proceeding. In order to paint the inside of your fireplace, it is necessary to thoroughly clean the surface first. If you intend to use your fireplace as a fire pit, you’ll need to choose paint that has been specifically developed to resist extreme temperatures. The majority of these paints are capable of withstanding temperatures of up to 1200 degrees. There’s still a potential that the paint will peel and split after a year or two.

Because a fireplace is such an important aspect of any home’s interior design, it is important to consider the color of paint not only around the fireplace but also throughout the room.

Choosing Colors

No matter what color you choose for the interior of your home, your fireplace will be the focal point, but color selection is critical to the overall design. Make your fireplace’s interior match the color scheme of the rest of the room by choosing colors that are similar in tone. Selecting contrasting hues is a great way to make a strong design statement. If you’re decorating the inside of a fireplace, a bright, fiery hue like lipstick red would be a good option, whereas a neutral color would be the ideal choice for the walls.

Finally, whether or not you want to use your fireplace to burn wood will have an influence on the color options available for the interior of your fireplace.

Painting the Room

Remove all of the switch plates and wall hangings from the room. If you’re painting over a semigloss or high-gloss finish, make sure to properly dust the walls and sand them before you begin. Painter’s tape should be used to mask whatever you wish to keep protected, such as baseboards, trim, light fixtures attached to the wall, and so on. Your first coat should be a primer that has been colored to match the final color of your topcoat. You may also purchase paint that has primer already mixed together with it.

To apply a second or third coat, let 24 hours to pass between each application.

Cleaning the Inside of a Fireplace

To correctly paint the interior of a fireplace, it is necessary to thoroughly clean it first. Remove the ashes from the fireplace and set them aside. Put on your safety gloves and goggles before scrubbing the interior of the vehicle with trisodium phosphate, or TSP, using a stiff steel brush. It is possible that you may need to wash the inside of the fireplace several times with TSP. When you’re finished, wipe off the inside of the fireplace with a clean, moist towel to ensure that all of the TSP residue has been removed.

See also:  How Much Does An Interior Architect Make

Painting the Inside of a Fireplace

Painter’s tape can be used to mask off the fireplace and any other sections that you don’t want painted throughout the painting process. Apply a layer of galvanized etching primer before painting over metal if you’re painting over a metal surface. In order to enjoy a fire in the fireplace, you must use high-temperature paint for your topcoats on brick or metal surfaces, rather than regular paint. Grills may also be painted using high-heat spray paint, but no matter which type of paint you choose, make sure to follow all manufacturer’s instructions carefully before doing so.

Allow 24 hours for your initial coat to dry completely before applying a second coat if the first coat did not provide adequate coverage.

Remove the masking tape once the paint has dried completely. A painted firebox can be used to house tiny wood burning stoves or even candles, which helps to prevent a fire from spreading directly to the paint.

How To: Paint a Brick Fireplace

  • Mild liquid dish soap, stiff-bristle brush, trisodium phosphate, bleach, wire brush, acrylic caulk, mild liquid dish soap See the whole list »
  • Tape for painting
  • 5 gallon buckets
  • Paint bucket screens
  • Masonry primer
  • Acrylic latex paint
  • Drop cloth
  • Paint roller frame
  • 1 1 4 inch thick nap roller cover
  • Telescopic roller extension pole
  • 2-inch paintbrush

Image courtesy of fotosearch.com

Step 1

It is necessary to moisten and clean the brick fireplace before painting it in order to ensure better paint adherence because of the tendency of brick to acquire grit. Clean the front of the brick fireplace using a stiff-bristle brush dipped in soapy water to remove grime and efflorescence, which are white, powdery mineral deposits that form on the bricks. If there is still soot in your fireplace after cleaning it, use a combination of 1/2 cup trisodium phosphate and 1 gallon of water to clean it.

To clean your brick, apply diluted bleach to the surface and allow it to soak in for 30 minutes before scrubbing the surface with a wire brush.

Step 2

Small cracks in the brick of the fireplace should be looked for. If you come across any, you may fill up the gaps using acrylic caulk purchased from your local home improvement store. Before continuing, double-check the bottle’s directions for the amount of dry time necessary.

Step 3

Cover the sections surrounding the fireplace that you do not want to paint with painter’s tape, such as the joints where the brick meets the floor and walls, with the tape. Drop cloths are used to protect the floor and the hearth of the fireplace from splatters of paint. Don’t feel like doing it yourself? Get free, no-obligation quotes from professional painters in your area.+

Step 4

Fill one of the 5-gallon buckets halfway with masonry primer and insert a bucket screen on the other end; this painting tool will aid you in both limiting mess and producing an even application on your roller with less effort. Now, dip the roller into the bucket and roll it around the screen, repeating the process until the screen is thoroughly coated with primer, if needed. Application of the initial coat should be done with care, covering the whole surface of the brick and ensuring that you get into the mortar joints as well.

If your brick construction extends all the way to the ceiling, you may want to consider bringing in a telescopic roller extension pole to assist you in reaching difficult-to-reach regions towards the top of the fireplace structure.

Wash your painting equipment and set them aside to dry overnight while you wait for the priming to be entirely dry.

Step 5

Prepare your acrylic latex paint the following day in the same manner as you did your primer, using a second 5-gallon bucket with a bucket screen to hold your prep materials. (While you may use any paint finish you choose, a matte paint is very effective in enhancing the natural grain of the brick.) Then, put your roller into the paint bucket and coat it evenly with paint, finishing with a second coat.

Apply a generous top layer of the paint to the brick, using overlapping strokes to ensure that all nooks and crannies are covered as much as possible, and let it to dry completely.

Step 6

With the brush, do any necessary paint touch-ups, and then thoroughly wash all of your equipment before the paint has a chance to dry. When you’re finished, remove the painter’s tape and drop cloth from the area around the fireplace and put them away. If you come across paint spatter in an unexpected location, simply wash it away with a soft cloth dampened with warm water—the sooner you do it, the better! Otherwise, all that’s left to do is stock up on kindling so that you may enjoy your newly-renovated fireplace this winter season.

Get free, no-obligation quotes from professional painters in your area.+

DIY: How to Paint a Brick Fireplace

The author, Sarah, is a wife and stay-at-home mom who likes writing on topics such as parenthood, healthy living, budgeting, as well as everything related to the home and garden. Before and after photos of a painted brick fireplace

Can You Paint a Brick Fireplace?

When we built our family room onto the rear of our all-brick ranch house, we knew we wanted to keep a portion of the brick wall exposed to serve as a backdrop for our wood burning fire. However, we ran into a major problem: the brick was too crumbly to utilize. It was old, dirty, and crimson, which was the exact opposite of the color scheme I desired in my family room. We came to the conclusion that we should paint the brick, but my husband was not convinced. Wouldn’t painted brick have the appearance of being.well, painted?

  1. I was sceptical at first.
  2. Isn’t it true that I’d need to hire an expert for this?
  3. Painting the brick was really rather simple and affordable, requiring just three quarts of high-quality paint and a few other painting supplies to complete.
  4. Although clean, the room is drab and red.
  • 1 gallon of primer
  • 1 quart each of three complementary paint colors (I chose Sherman Williams Mindful Grey, Accessible Beige, and White Duck)
  • 1 gallon of gesso
  • 1 gallon of sandpaper Brushes: 3″ paint brush, stiff brush, little sea sponges

Choosing Colors

This might be the most difficult aspect. I’m joking, of course. It’s not even close to being rocket science. Light beige or cream for the base coat and grout color, a medium beige or gray for the contrast color, and a light cream for the final coat or highlighter were some of the colors I considered. If you are apprehensive about picking color combinations on your own, a color-combination card from your local home improvement store is a good place to start. You may be surprised at how simple it is to paint a brick surround.

Step 1: Clean Everything

The first thing I did was thoroughly clean the brick.

How to Clean Brick

  1. I scraped the trash and grime off the wall with a stiff-bristled brush, making my way down from the top to the bottom. The wall would have needed to be entirely dry if there had been any filth or grease on it, so I would have followed up with a cleaning solution and a thorough rinse before moving on. In reality, this Fireplace cleaner was used by my mother and myself when we were cleaning her brick fireplace. Afterwards, I swept the floor underneath the portion of wall I was painting to remove any remaining creosote
  2. I completed by painting the rest of the wall.

To be on the safe side, remember that painting brick is a dirty, paint-tossing endeavor. However, unlike me, you will most likely be painting in a finished area, which will require protection from paint splatters and overbrushing. I was fortunate in that I was able to work in an unfinished room. Make sure to shield the walls and floor surrounding your brick from any damage.

You could purchase specific plastic sheets, but it may be more cost-effective to simply go to Goodwill and get a cheap bed sheet. Thank you very much. This is the piece of the wall that will be left exposed during the renovation. It’s primed, and I’ve begun painting the base color on top of it.

Step 2: Prime the Brick (2 Coats of Primer)

The exciting part is about to begin. The entire wall should be painted using a primer that is authorized for brick using a 3″ or bigger paintbrush. The first layer will be applied very slowly since brick may absorb a great deal of paint! Maintain a generous amount of primer on the brush at all times, but evenly apply the paint, keeping an eye out for paint drips along the mortar lines. Begin at the top of the wall and make your way all the way down to the ground. Painting in small portions, first painting the mortar lines, then painting the bricks in each section before going on to the next section.

  • The second coat should be applied far more quickly than the first.
  • Is it possible that I have said that?
  • To be sure, if your brick has already been painted, and you are only changing the colors, you may avoid this step—unless you have concerns with mold, mildew, or stains, in which case you should proceed.
  • Regular primer, such as that used to prime drywall, may not adhere as effectively to brick.
  • Following the application of the base coat, the wall was painted.

Step 3: Apply the Base Coat

The fun begins! Using a clean paintbrush, apply a thick base coat. Again, you’ll want to work from top to bottom and paint the mortar lines first before painting the brick. Now, you could leave the wall one solid color at this point—apply a second coat of mindful grey and call it a day, but where’s the fun in that? Note:The color variation you see in the picture is because some of the paint was still wet when I took that shot. In reality, the wall was one beautiful, solidly colored wall, and I really was tempted to leave it just like that.

Notice that the shading is varied and sporadic.

Step 4: Apply the Contrast Color

As soon as the base coat is applied, it’s time to apply the contrast color, which in this case was Accessible Beige. Alternatively, you may wait for the base coat to dry, but I prefer the way the contrast color blends somewhat with the base coat, slightly changing the hue. Making use of the sponge, dab the beige paint onto each brick, taking care not to get any paint into the mortar lines. It is necessary to leave the lines grey in order to get the fake brick appearance. For this period, work in small parts, sponging paint onto one brick and then applying it to adjacent bricks in a radial manner around the initial brick.

Wait to apply more paint to the sponge until the paint begins to go on very faintly before adding more paint.

The temptation to become disheartened can be strong right now.

Continue to paint. Put your faith in the process. Please keep in mind that you may want to brighten up your fireplace while you’re at it as well. Rust-Oleum Stove Paint has been carefully designed to withstand the extreme temperatures that your fireplace will generate.

Step 5: Apply the Highlighter

This is the final phase, and you can do it! Start applying the highlighter and final coat before the contrast color has had a chance to dry completely, without washing your sponge between coats. Begin in the center of the wall and select a brick to paint with solid White Duck to create a focal point. Repeat this process on the bricks surrounding the initial brick until your sponge begins to run out of paint. Afterwards, take a step back and select the next block to paint completely solid, and continue the process.

See also:  How To Install An Interior Barn Door

I painted a few bricks nearly completely white, a few bricks with just a smidgeon of white paint, and the rest were a mix of colors all over the spectrum.

To paint in a circular pattern on the wall, take a step back every few bricks to take a good look at the entire wall to ensure that you like how it appears and to plan where your next light brick will be placed.

If you don’t like what you’ve done so far, you can always go back and add additional highlighter or contrast color later on.

A Word About Paint

Regular paint is not designed to resist prolonged exposure to high temperatures. In my situation, the wood stove had not yet been installed, so I was able to have it set up such that it was flush with the drywall, which only protruded about a foot or so from the wall when fully operational. At the end of the day, I felt most comfortable using a conventional paint. A product by Sherman Williams called Powdura, which is designed to resist temperatures of up to 200 degrees Fahrenheit, is also available.

They sell paint that has been carefully formulated for fireplace and wood stove surround applications.

I have not personally utilized them, so please do your own research and read reviews before deciding to use them.

Tips For Painting Brick to Look Natural

For those of you who have never sponge-painted a wall before, this section will be of particular interest. Don’t be sucked in. Dip the sponge in the paint, but don’t immerse it, then tap it on a flat surface to remove some of the excess paint, if necessary. Then, using the sponge, carefully dab the brick you wish to paint with the paint. Paint the entire brick surface with a thick coat of paint and a sloppy hand. To enable the previous layer to show through, use a softer hand and less paint than usual.

  1. When painting your wall, you will want to use a combination of a few heavy coats and a few light coatings with a variety of everything in between to get the variegated appearance of brick.
  2. Take a risk!
  3. Method.
  4. Even on the same brick, try to avoid painting in a straight line wherever possible.
  5. Then paint the bricks immediately surrounding that brick with the same color as the first.
  6. Take a step back.
  7. What specifically are you looking for?

Do you appreciate how dark or light the wall is?

As they dried, I noticed that certain places were a touch dark, so I used the highlighter to bring them up in contrast to the rest of the piece.

When I took a step back from the wall, I observed that some of the bricks appeared to be “painted.” My sponging did not appear to be natural.

Avoid Predictable Patterns at all costs.

Avoid using a predetermined pattern; you want spontaneous variation in shade.

If you look closely at my wall, you’ll see that I only have a few bricks that are really bright in color and a few bricks that are quite dark in color.

Painted Brick Wall that has been completed That’s all there is to it!

I still can’t believe how much has changed!

I’d be interested in hearing how it goes! While the information contained within this article is factual and truthful to the best of the author’s knowledge, it should not be used as a substitute for formal and personalized counsel from a competent expert.

QuestionsAnswers

Question:Have you ever heard of a brick stain that is particularly made for use in a fireplace that uses them? Answer:Yes. Painting the brick instead of staining it was my first choice since I wanted a more dramatic transformation. The original brick was red, and I wanted the new brick to be white and beige to match the existing brick. Question:Was the paint on your brick wall flat, semi-gloss, or high gloss in appearance? It was a semigloss finish, to be precise. Sarah’s Year in Review 2015

Love the Post? Leave a Comment Below. I’dLove Your Feedback!

Nicole Currieon is a model and actress. The 19th of October, 2019: This worked well! [email protected] SherWIN Williams, not SherMAN Williams, is the name of the company on August 25, 2019. poetryman6969on Tuesday, August 2, 2015: This is an intriguing method.

How to paint a brick fireplace (the right way)

If you want to paint a brick fireplace the proper way, this straightforward step-by-step instruction will answer all of your concerns, including which colors work best, what paint sheen you should use, and if chalk paint is a good idea. We have a brick fireplace in our family room that is extremely unattractive. When we initially moved here, the house was an unpainted red brick, which I despised. My dislike of orangey-red brick was already a problem, but our fireplace was made worse by some shoddy mortar lines that were visible through the opening.

  • I had no qualms about painting the brick white as soon as we moved home, and I had no hesitations about it.
  • Huge.
  • Every now and again, I get a completely crazy notion for my house.
  • Some of those outlandish ideas have grown into some of my very favorite features in my house.
  • However, there were a few snags along the road that I am very thrilled with the outcome.
  • In order for you to benefit from my experiences, I’m sharing what I’ve learnt with you now so that you may avoid making the same mistakes I did.
  • Please note that affiliate links are used in this post.

What sheen to paint a brick fireplace – matte or satin?

I started by painting the fireplace with chalk paint, which turned out to be just stunning. Nevertheless, I became sidetracked and did not seal it straight away. Furthermore, as my kid drove his miniature cars all over the fireplace, the paint became somewhat scraped up and damaged. After painting it with chalk paint, I decided to refinish it with glossy latex paint in a color that was an identical match to the chalk paint color I had previously used (a terrible error). In addition, by the time I was completed, it no longer appeared to be spectacular.

  • The satin paint is used on the portion of the right side that is more reflective.
  • I’m not really sure how to explain it, but the actual paint on the glossy side was the only thing that caught my eye.
  • The matte side of the chalk paint side looked like it belonged, but the shiny side did not appear to belong at all.
  • I don’t believe it had anything to do with the fact that I used latex paint instead of chalk paint.

Because brick has a matte surface to begin with, it stands to reason that matte paint will look much better on brick. Learning experience gained, in the future I will only use matte paint on brick, regardless of whether I am painting with plain old white paint or anything else.

Can you chalk paint a brick fireplace?

As previously said, I originally intended to use chalk paint. In addition to being a beautiful hue, this product was very easy to work with and had a nice matte finish. (The chalk paint I used was Americana Decor Chalky Finish Paint, which you can find on Amazon. A unique color was created by combining the hues Legacy and Relic.) Unfortunately, without a protective top coat, it did not prove to be long-lasting. If you are painting with chalk paint, this is typically the norm for everything you are painting whether it is furniture, home décor, or even cloth.

  1. My youngster enjoys playing on the hearth of the fireplace, which may have been acceptable if no one ever touched it in the past.
  2. So, if you do decide to use chalk paint on your fireplace, I strongly advise you to apply an excellent sealer to protect your investment.
  3. If I were to use chalk paint, I would follow it up with General Finishes Flat out Flat Topcoat to give it a smooth finish.
  4. Alternatively, you may save time and effort by using a matte latex paint and omitting the requirement for a sealer altogether.

Materials for Painting a Brick Fireplace

  • Cleaner, painter’s tape, primer, latex paint in a matte or flat finish (I chose Sherwin Williams Blue Mystery), stiff paintbrush, and a pair of scissors.

How to Paint a Brick Fireplace (the right way)

Prior to painting anything, it must first be thoroughly cleaned. And fireplaces, in particular, are prone to being encrusted with soot, ash, and other fine particles of dust. A spray bottle filled with water and Dawn dish soap works best for me when doing projects like this, but any basic cleaner should do the trick. As you clean, be sure to get into all of the nooks and crannies. You may also want to use painters tape to cover any trim or flooring that will come into contact with the brickwork.

Do you need primer?

The first layer of priming is absolutely necessary when painting brick that has never been painted before. Brick is a porous material that absorbs a lot of paint. Starting with primer will allow you to reduce the number of coats of paint you will need substantially. It is possible to skip the priming step if your brick has already been painted and you are confident that it was coated with a water-based paint, as described above. However, if you have an older property and the brick has been painted for a long period of time, there is a significant probability that the paint was an oil-based product.

If you suspect that your fireplace was painted with an oil-based paint, you may test it by rubbing a little amount of nail polish remover (including acetone) on the paint surface.

If you have previously painted your fireplace with an oil-based paint, you have two options to consider.

On a general basis, I favor the second alternative. Water-based paints are quite durable these days, and they are also better for the environment, as well as being much simpler to work with and clean up afterward.

Painting the brick

Painting brick takes a little time and effort, but it is not difficult. Because brick is so textured, you must work hard to get the paint down into all of the cracks and crevices. To begin, use your paintbrush to push paint into all of the mortar lines between the bricks with a downward motion. After that, simply go back over the bricks with your brush and paint the faces of the bricks. In the majority of situations, two coats of paint should be sufficient for adequate coverage. Make sure to let the paint to dry completely between layers.

Personally, I did not find it to be really effective in speeding things up.

Painting fireplace doors

During the same process, as you can see, I also painted the metal fireplace doors in white. Despite the fact that I would like to remove the doors for purely cosmetic reasons, they make a significant impact in terms of helping to manage the temperature in our house. As a result, they must remain for practical reasons. But at the very least, I wanted to make them more inconspicuous. This is a rather simple procedure: simply tape off the glass and the masonry surrounding the doors, then spray the doors with a high heat spray paint to complete the job.

  • I’d never seen a navy fireplace before, but it’s one of my favorite designs.
  • I regret nothing.
  • The difference that paint and some low-cost timber can make is quite astonishing!
  • I would much appreciate it if you would pin this page to your Pinterest board.

Materials

  • Latex paint in a matte or flat finish (I used Valspar Blue Mystery for this project)
  • Cleaner
  • Painter’s tape
  • Primer

Instructions

  1. Completely clean the fireplace, taking special care to clean all of the nooks and crannies along the way
  2. Painter’s tape may be used to preserve any trim or flooring. Prime the brick fireplace with a layer of paint to protect it. Allow to dry
  3. Using a paint brush, paint the brick, being sure to get into all of the mortar lines between the bricks. You’ll need at least two coats. Allow for drying time between applications.

Learn how to paint a brick fireplace with this Google Web Story.

See also:  How Much Is An Interior Detail

How Do You Pick the Best Paint for a Brick Fireplace?

When it comes to painting your brick fireplace, you’re not alone; you’re in excellent company. Making a fresh, new appearance for your home is a common and economical technique to do it. “When a full-scale rebuild is not necessary, one of my favorite methods to renew a brick fireplace is to simply paint it,” says Jill Romine, a New York-based designer.

“When red or brown brick doesn’t work for your own style, a simple and inexpensive solution is to appreciate the texture, depth, and dimension of the material while using paint to adjust the color to more closely match your design approach.”

Choose the Right Paint

The first step in preparing to paint your brick fireplace is to select the appropriate paint. To choose which paint is the greatest fit for your needs, you should ask yourself a few questions.

Will You Be Using the Fireplace?

To begin painting your brick fireplace, the first step is to select the appropriate paint color for your fireplace. Asking yourself some questions can help you choose which paint is the best choice for you.

What Sheen Do You Want?

Sheen refers to how reflective the paint is — that is, how much light it reflects – and how glossy it is. Eggshell has a lower gloss and emits a warm light when illuminated. It’s less difficult to apply and exposes fewer defects, which is crucial because fireplace brick has a textured surface, making it a good choice for this application. Because it is more difficult to apply and reflects a great deal of light, semi-gloss may be obtrusive in a bright setting. However, it is less likely to discolor and is simpler to clean.

What Color Do You Prefer?

Fireplaces may be painted in any color you like, just like the walls in your home. So, how do you cut it down to a manageable number? It all depends on the aesthetic you’re going for. If you like the color of your bricks but your fireplace is discolored or simply needs a refresher, you may paint it the same color as the bricks. White is a great color to use to give your area a crisp, new appearance. Do you like a more rustic look? Try whitewashing the brick, which will allow some of the hues of the brick to shine through a little.

The colors Black Magic PPG1001-7 and Admiralty PPG1042-7 from PPG Paint, according to Romine, “would create quite an eye-catching statement in moodier, bolder rooms.” “It’s vital to understand that contrasting colors on trimmings, mantles, and base moldings (also known as finish carpentry) will frame the painted brick fireplace, making it visually shine as a prominent design feature in your room,” Romine explains.

As an alternative, painting the brick a similar color to the finish woodwork will help the brick blend in and vanish into the building.”

Some Other Things to Consider

A few of other considerations should be taken into consideration while painting a brick fireplace. Because of the flue, even if you aren’t burning flames in your fireplace, it is still more susceptible to moisture buildup than the interior walls of your home. As a result, it’s critical to prime the brick with two coats of masonry primer before painting it with acrylic paint. Not only does this provide the ideal surface for painting over, but it also helps to prevent stains from forming on the brick when it is exposed to moisture over extended periods of time.

It is likely that painting will exacerbate these problems by sealing the brick, enabling moisture to accumulate, and making it difficult (if not impossible) to repair the mortar.

Check for cracks in the masonry and fix them with acrylic caulk if they are minor.” If you have the correct paint for the job, painting a brick fireplace may be a pleasant weekend endeavor.

And if you’d like to have a professional do it for you, we can assist you. Request a free quotation, explore samples of PPG paint colors, and read customer testimonials. We are only satisfied when our consumers are satisfied.

Painting The Interior Of A Fireplace

At the end of October, we’ve already experienced a couple fires this year, with many more to come in the next weeks and months. Given the fact that my eldest, Peter, will be attending college the following year, I try not to get too sentimental on Sunday afternoons, but oh, how I enjoy having everyone at home watching football or a movie, our three children and their friends sprawled out on the floor and couch in front of the fireplace in our small family room. I just adore it. A fire makes the house seem so warm and inviting, and now that we have remodeled the fireplace, we spend most of our time in this area during the colder months.

  • The old firebox needed to be cleaned up after the hearth and surround were tiled and painted, so I thought I’d share a couple of my thoughts with you on the job as it progressed.
  • My entire disclosure policy may be found here.
  • Take the grating out of the way.
  • Scrape away any ash that has accumulated on the walls of the firebox, vacuum, and then clean off the interior of the box with moist old rags.
  • It is capable of withstanding temperatures as high as 1200 degrees Fahrenheit.
  • THREE |If you truly use your fireplace, as we do, avoid painting the areas where the flames come into direct touch with the fireplace box.
  • I didn’t paint the backplate or grate; instead, I painted the firebrick on the inside of the firebox walls.

Painting the interior black obviously brightens things up, but if you have a wood burning fireplace, you have to accept that the bottom of the firebox will become sooty over the course of the season and will remain sooty.

Many people have inquired about the white paint that I used on the inner border of the fireplace box, which has received a lot of attention.

Although I tiled the two inner brick walls that meet the marble surround originally, they didn’t seem quite right, so I removed the tiles and wiped out any remaining mortar.

I enjoy how the paint doesn’t draw too much attention to itself, and because it isn’t in direct touch with the heat, I’m not concerned about it releasing toxins into the environment.

It’s just wonderful!

By the end of the winter, the front of the fireplace would be completely coated with smoke stains.

It was said to have removed smoke from entering a room by directing the smoke towards the chimney, among other things.

This increases the efficiency of a fire’s combustion and the amount of heat it produces.

Long story short, we are huge fans of theirs.

Mark could work as a sales representative for Grate Wall Of Fire in his spare time because he tells everyone about it:).

The search for a fireplace screen that won’t cover up my beautiful tile has been fruitless, and finding one that’s exactly perfect is proving to be quite tough.

I’ll keep you informed as the hunt progresses.

I believe I’ve had enough of them. Already, I’d say. Friends, I hope you are having a wonderful week! In case you’re interested in getting the inside scoop on the fireplace remodel, check out these posts: It is necessary to tile both the surround and the hearth.

My Painted Brick Fireplace – DIY Tutorial –

If you have a brick fireplace, you may have thought of painting it to give it a more modern appearance. In today’s post, I’ll guide you through the processes I took to complete my painted brick fireplace in one day, as well as the supplies I used (hint: it’s not paint). A spray bottle filled with water, rags, a masonry brush, and Romabio Limewash are all that are required. The moment we closed on the purchase of our first home, I knew one of the very first tasks I wanted to complete was painting our brick fireplace.

  • My husband and I were tired of the red and orange overtones in the paint, and I wanted a softer, more neutral appearance in our house.
  • I went to Pinterest to look for inspiration and came across a plethora of photographs of fireplaces with white painted brick surrounds.
  • It turned out that there were numerous methods for white-washed brick that were more sheer in coverage, but it wasn’t the style I was going for either.
  • It’s a real lime paint that has been specially developed to provide a distinctive lime wash appearance on stone, brick, and other masonry surfaces, according to the manufacturer.
  • You may learn more about ithere by visiting their website.
  • Most appealing to me is that you can create a unique design just by varying the way it is applied, and you may cover the brick to whatever extent or degree that suits your needs and preferences.
  • This made it appear less permanent and frightening.

The use of varied colored bricks, in my opinion, adds additional depth and authenticity to the design.

This product truly works like magic!

You can’t make a mistake, I’m serious.

Do not be taken in by this ruse.

Here’s the step-by-step procedure I used to complete it.

I began by cleaning down the brick with a moist towel to ensure that I had a clean surface on which to work before proceeding.

Drop cloths should be placed over your mantle and the floor surrounding your fireplace, since you will dribble on them!

I used a large spray bottle loaded with water to wet down the brick fireplace until it was completely covered.

I combined the two colors I was using in two separate 5-gallon buckets, following the guidelines on the back of the can for a 1:1 ratio of water to limewash solution.

There is no need to prime lime wash because it is designed to work with brick and stone while still allowing it to breathe.

4.

I highly recommend using a masonry brush for this stage because it is far bigger than a paint brush and hence moves much more quickly.

*Update: I observed that one of the reviewers did not enjoy the masonry brush.

Continuing down the chimney, I painted random bricks and worked my way up.

When I completed painting the bottom of the fireplace with Nube Gray and had made it all the way to the bottom, I followed it up with my bucket of Avorio White and began applying the lime wash with my masonry brush, starting at the top of the fireplace once more.

I was pretty haphazard in my painting approach and did not make an effort to paint properly around each Nube Gray brick.

The drips on the gray brickwork didn’t bother me at all, and I rather like how it made the space feel more realistic.

6.

This is one of the most attractive aspects of the product.

I wanted it to be fairly fully covered so that none of the red brick could be seen through, so I didn’t wipe off much of the surface area. That’s how you lime wash a fireplace, by the way.

Living Room Sources:

  • Animal print rug (which is incredibly soft! )
  • Leather ottoman
  • Leather chairs
  • Sofa – which was custom ordered
  • Charcoal curtains
  • Plant stand
  • And more.

It’s truly as straightforward as that! I completed the limewashing of the fireplace by myself in one day, and it only required a few hours of labor. The process of using two colors took longer, but I believe it was well worth it, and I am pleased with the results! Within a few hundred dollars, I was able to entirely remodel our fireplace. Romabio lime washenough, I cannot scream the praises of this product! I updated the old gold fireplace cover by spray painting it with a high-temperature matte black spray paint to give it a more contemporary appearance.

I’m thrilled with how everything turned out!

It’s a really pleasant and comfortable place to be.

That particular rug is from an internet rug business that has incredible prices and frequently has deals going on.

Because the rug is on the thin side, and I prefer my rugs to be thick and plush, I would recommend adding a rug cushion below the rug for added comfort.

By the way, if you’re interested in learning how to install a television over a brick fireplace, this guide demonstrates exactly how we accomplished it while concealing the wires.

Leave a Reply

Your email address will not be published.